Vibration Damper and Pulley - Remove and Install
拆卸步骤
- 将螺栓 (2) 、曲轴减振器 (3) 和隔套从曲轴皮带轮上拆下。
注: 有关 3114 和 3116 发动机减振器的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8220, "3114 和 3116 发动机减振器检查的技术规格"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
图 1 | g00691836 |
- 释放水泵驱动皮带 (1) 的张力。 拆下曲轴皮带轮上的皮带。
- 拆下螺栓 (4) 和垫圈。
Show/hide table
图 2 | g00691831 |
- 拆下曲轴皮带轮 (5) 。
注: 有关曲轴皮带轮的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8046, "铸铁和钢制皮带轮"。
安装步骤
- 在曲轴上定位曲轴皮带轮 (5) 。 安装螺栓 (4) 并拧紧螺栓至扭矩为 160 ± 30 N·m (118 ± 22 lb ft)。
注: 有关曲轴皮带轮的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8046, "铸铁和钢制皮带轮"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 3 | g00691831 |
- 安装水泵驱动皮带 (1) 。
注: 检查橡胶减振器上的对准标记,以确保正确的对准。 如果橡胶减振器不能对准,则更换橡胶减振器。 请参阅技术规格, "减振器"。
Show/hide table
图 4 | g00691836 |
- 安装隔套和曲轴减振器 (3) 。 将螺栓 (2) 拧紧至扭矩 55 ± 10 N·m (40 ± 7 lb ft)。
注: 有关 3114 和 3116 发动机减振器的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8220, " 3114 和 3116 发动机减振器检查的技术规格"。
- 调整水泵驱动皮带 (1) 的张力。 请参阅技术规格模块, "皮带张紧力表"。 另请参阅操作和保养手册, "皮带 - 检查"。
Caterpillar Information System:
3176C and 3196 Marine Engines Heat Exchanger - Remove
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Can Not Reach Top Engine RPM
3516B Engine for Caterpillar Built Machines Symptoms
3500B Engines Engine Monitoring System
3176C and 3196 Marine Engines Exhaust Manifold - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Cat Data Link
3176C and 3196 Marine Engines Air Cleaner - Remove and Install
3512B and 3512C Engines For Caterpillar Built Machines Load Feedback Capability
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Customer Parameters Worksheet
C15 and C18 Petrolem Generator Set Engines Factory Passwords
3176C and 3196 Marine Engines Aftercooler - Install
Replacing the Transformer in the Automatic Transfer Switch{4469} Replacing the Transformer in the Automatic Transfer Switch{4469}
2000/02/01 Solenoid Available To Service Hydrax Actuators {1259}
3176C and 3196 Marine Engines Heat Exchanger - Install
3508B Industrial Engines Turbocharger
3176C and 3196 Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3176C and 3196 Marine Engines Water Outlet Manifold - Remove
3126B Engines Finding Top Center Position for No. 1 Piston
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Engine Cranks but Will Not Start
2000/02/01 Revised Oil Level Gauge Calibration Chart for 3412E Marine Engines {1326}
3176C and 3196 Marine Engines Water Outlet Manifold - Install
2000/02/01 New Method To Determine When To Clean The Aftercooler Core {1064}
G3304 and G3306 Engines Test Tools for the Cooling System
3176C and 3196 Marine Engines Engine Support (Front) - Remove and Install