Engine Oil Filter Base - Disassemble
Disassembly Procedure
Start By:
- Remove the engine oil filter base.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove three O-ring seals (6) from the oil filter base.
Show/hide table
Illustration 1 | g00849489 |
Typical example |
- Remove relief valve assembly:
- Loosen bolt (1) slowly in order to release the compression on the spring (3) .
- Remove the following items from the oil filter base: bolt (1), seat of the relief valve spring (2), spring (3) and retainer (4) .
- Remove spacer (5) from bolt (1) .
- Remove the two bolts and the washers that hold valve (11).
Show/hide table
Illustration 2 | g00849701 |
Typical example |
- Remove valve (11) and O-ring seal (9) from oil filter base.
- Remove the two bolts and the washers that hold cover (10) .
- Remove the following items from the oil filter base: cover (10), O-ring seal (9), spring (8) and oil pump bypass valve (7) .
- Remove the following items from oil filter base: cover (12), O-ring seal (13), spring (14) and relief valve plunger (15) .
Show/hide table
Illustration 3 | g00850052 |
Typical example |
- Remove the stud that holds the oil filter to the oil filter base, if necessary.
Caterpillar Information System:
3176C and 3196 Marine Engines Engine Oil Filter Base - Install
2000/05/01 New Format of PC Software for Customer Communication Module {1926}
3176C and 3196 Marine Engines Engine Oil Filter Base - Remove
3176C and 3196 Marine Engines Electric Starting Motor - Remove and Install
3408E and 3412E Industrial Engines Valve Rocker Arms and Lifters
C-12 Marine Engines Cylinder Head - Install
3176C and 3196 Marine Engines Rocker Shaft and Pushrod - Install
3176C and 3196 Marine Engines Speed/Timing Sensor - Remove and Install
3176C and 3196 Marine Engines Crankshaft Rear Seal - Install
2000/02/01 Correction to Specifications Module, SENR6436-00, "3114 & 3116 Diesel Truck Engines" {1201}
3176C and 3196 Marine Engines Crankshaft Rear Seal - Remove
3176C and 3196 Marine Engines Crankshaft Front Seal - Install
3176C and 3196 Marine Engines Engine Oil Filter Base - Assemble
3176C and 3196 Marine Engines Engine Oil Cooler - Remove
3126B and 3126E On-highway Engines Customer Passwords
325D and 329D Excavators Hydraulic System Cylinders (Boom, Stick and Bucket)
3176C and 3196 Marine Engines Engine Oil Cooler - Install
3176C and 3196 Marine Engines Engine Oil Pump - Remove
3176C and 3196 Marine Engines Engine Oil Pump - Install
3176C and 3196 Marine Engines Engine Oil Pump - Disassemble
3176C and 3196 Marine Engines Engine Oil Pump - Assemble
3176C and 3196 Marine Engines Engine Oil Pan - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Cylinder Head Valves
3176C and 3196 Marine Engines Engine Oil Pressure Sensor - Remove and Install