Aftercooler - Remove - High Performance Aftercooler
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7574     | 连杆支架     | 2     |
B     | 138-7575     | 连杆支架     | 2     |
开始:
- 拆下排气歧管。 请参阅拆解和组装, "排气歧管 - 拆卸和安装"。
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下螺栓 (1) 、垫圈和挡圈 (2) 。 拆卸管组件 (3) 。
Show/hide table
图 1 | g01286635 |
- 从管组件 (3) 拆下密封垫。
- 拆下螺栓 (4) 和垫圈。
Show/hide table
图 2 | g00609932 |
- 拆下螺栓 (5) 和垫圈。 卸下支架 (6) 。
Show/hide table
图 3 | g00609944 |
- 拆下将管 (8) 连接到涡轮增压器的螺栓 (7) 、螺母和垫圈。 拆卸管 (8) 。
Show/hide table
图 4 | g00609951 |
- 将空气管 (9) 从后冷器壳体 (10) 上拆下。
Show/hide table
图 5 | g00609971 |
- 拆下螺栓 (11) 和垫圈。 取下后冷器壳体 (10) 。
Show/hide table
图 6 | g00609978 |
- 将密封垫从后冷器壳体 (10) 上拆下。
- 拆下螺栓 (13) 和垫圈。 从后冷器盖组件 (14) 上拆卸适配器 (12) 。
Show/hide table
图 7 | g00609990 |
- 将密封垫从适配器 (12) 上拆下。
- 拆卸螺栓 (15) 和垫圈。 拆卸挡圈 (18) 。
Show/hide table
图 8 | g00609995 |
- 拆下法兰 (17) 、油孔 (16) 和板 (19) 。
- 卸下螺栓 (21) 、螺母和垫圈。 拆下卡箍 (20) 。
Show/hide table
图 9 | g00610015 |
- 拆下螺栓 (22) 和垫圈。
- 拆下螺栓 (23) 、垫圈和隔套。
Show/hide table
图 10 | g00610017 |
- 拆下卡箍组件 (24) 。
- 拆下管 (25) 。
- 将环和 O 形密封圈从管 (25) 上拆下。
- 拆下支架 (26) 。
Show/hide table
图 11 | g00610028 |
- 拆下螺栓 (27) ,然后拆下三通管接头 (28) 。
Show/hide table
图 12 | g00610031 |
- 拆下螺栓 (29) 和垫圈。
Show/hide table
图 13 | g00610065 |
- 拆下法兰 (30) ,并将三通管接头 (31) 连同密封件和油孔一起拆下。
- 拆下螺栓 (32) 和垫圈,并拆下支架 (33) 。 卸下弯管组件 (34) 。
Show/hide table
图 14 | g00610090 |
- 将密封垫从弯管组件 (34) 上拆下。
- 拆下螺栓 (36) 和垫圈。 将三通管接头 (37) 从法兰 (35) 上拆下。
Show/hide table
图 15 | g00610360 |
- 拆下螺栓 (38) 。 拆下弯头 (39) 。
Show/hide table
图 16 | g00610371 |
- 拆下将后冷器盖组件固定到后冷器芯组件上的螺栓 (40) 和垫圈。 卸下垫片 (41) 。
Show/hide table
图 17 | g00610378 |
- 如有必要,拆下后冷器芯组件和后冷器壳体之间的垫片 (42) 。
Show/hide table
图 18 | g00610397 |
- 将工具 (A) 和适当的起吊设备连接到前部盖组件 (43) 上。 前部盖组件 (43) 的重量约为 130 kg (287 lb)。
Show/hide table
图 19 | g00610405 |
- 拆下前盖组件 (43) 。
- 拆下螺栓 (45) 和垫圈。
Show/hide table
图 20 | g00610413 |
- 将工具 (A) 和适当的起吊设备连接到后部盖组件 (44) 上。 后部盖组件 (44) 的重量约为 85 kg (187 lb)。
- 拆下后盖组件 (44) 。
- 将工具 (A) 和适当的起吊设备连接到前部芯组件 (46) 上。 前部芯组件 (46) 的重量约为 280 kg (617 lb)。
Show/hide table
图 21 | g01286676 |
- 拆下前部芯组件 (46) 。
- 将密封件从前部芯组件 (46) 上拆下。
- 将工具 (A) 和适当的起吊设备连接到后部芯组件 (47) 上。 后部芯组件 (47) 的重量约为 150 kg (331 lb)。
Show/hide table
图 22 | g00610464 |
- 拆下后部芯组件 (47) 。
- 将密封件从后部芯组件 (47) 上拆下。
- 将弯管和管从前后冷器壳体 (48) 上拆下。
Show/hide table
图 23 | g00611115 |
Show/hide table
图 24 | g00611124 |
- 将工具 (B) 和适当的起吊设备连接到前部后冷器壳体 (48) 。 前部后冷器壳体 (48) 的重量约为 195 kg (430 lb)。
- 将螺栓 (49) 和垫圈从缸体上拆下。
- 拆下前部后冷器壳体 (48) 。
- 将工具 (B) 和适当的起吊设备连接到后部后冷器壳体 (50) 。 后部后冷器壳体 (50) 的重量约为 95 kg (209 lb)。
Show/hide table
图 25 | g00611132 |
- 将螺栓 (51) 和垫圈从缸体上拆下。
- 拆下后部后冷却器壳体 (50) 。
- 拆卸密封垫 (52) 。
Show/hide table
图 26 | g00611161 |
Caterpillar Information System:
G3612 and G3616 Engines Oil Temperature Regulators - Remove and Install
3126B and 3126E On-highway Engines Engine Control Module - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Assemble
G3612 and G3616 Engines Engine Oil Pan - Disassemble
3126B and 3126E On-highway Engines Alternator - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Install
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
C-9 Engines for Caterpillar Built Machines Engine Design
G3612 and G3616 Engines Engine Oil Pan - Remove
3126B Truck Engine Electronic Control System Components
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
3126B and 3126E On-highway Engines Fan Drive - Remove
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Install
3126B and 3126E On-highway Engines Air Compressor - Remove and Install
G3612 and G3616 Engines Priority Valve - Install
G3612 and G3616 Engines Priority Valve - Disassemble
G3612 and G3616 Engines Priority Valve - Assemble
G3612 and G3616 Engines Vibration Damper - Remove
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
3126 Truck Engine Military Air Compressor Drive Gear - Install
SR4B Generators Generator Operation
3126B Engines for Caterpillar Built Machines Crankshaft - Remove