Vibration Damper - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
B | 8T-0914 | 飞轮导销 | 2 |
4C-9426 | 减振器导向销 | 2 | |
1U-9392 | 减振器导向销 | 2 | |
1U-9393 | 减振器导向销 | 2 |
开始:
- 卸下减振器护罩总成。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 按照正常应用,选择导销。
- 卸下固定减振器 ( 2) 的两个螺栓 (1)。 安装工具 (A)。
- 将尼龙带穿过减振器 ( 2) 的中心,然后将其固定至起重机。 窄型减振器的重量约为
288 kg (639 lb) 。 宽型减振器的重量约为402 kg (886 lb) 。 - 卸下将减振器 (2) 固定至适配器的其余螺栓,然后卸下适配器。 拆下工具 (A)。
Show/hide table
图 4 g00609910 - 卸下固定适配器 ( 3) 和减振器 (4) 的两个顶部螺栓。 卸下工具 (B)。
- 卸下其余的螺栓,然后卸下适配器 ( 3)。
Show/hide table
图 5 g00609915 - 将减振器 (4) 移至工具 ( B),直至可以将尼龙带穿过减振器 ( 4) 中心。
- 将尼龙带固定至起重机,然后卸下减振器。 窄型减振器的重量约为
288 kg (639 lb) 。 宽型减振器的重量约为402 kg (882 lb) 。Show/hide table图 6 g00609918 - 卸下垫片 (5)。
Show/hide table
图 1 | g00609896 |
此图为 G3616 发动机 减振器护罩 (X) 的图示。 |
Show/hide table
图 2 | g00609902 |
此图为双重减振器的图示。 |
Show/hide table
图 3 | g00609906 |
注: 以后的减振器带有翅式护盖。 小心不要损坏翅片。
Caterpillar Information System:
G3612 and G3616 Engines Priority Valve - Assemble
G3612 and G3616 Engines Priority Valve - Disassemble
G3612 and G3616 Engines Priority Valve - Install
3126B and 3126E On-highway Engines Air Compressor - Remove and Install
3126B and 3126E On-highway Engines Fan Drive - Install
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Remove
3612 and 3616 Engines Aftercooler - Remove - High Performance Aftercooler
G3612 and G3616 Engines Oil Temperature Regulators - Remove and Install
3126B and 3126E On-highway Engines Engine Control Module - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Assemble
G3612 and G3616 Engines Engine Oil Pan - Disassemble
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
3126 Truck Engine Military Air Compressor Drive Gear - Install
SR4B Generators Generator Operation
3126B Engines for Caterpillar Built Machines Crankshaft - Remove
G3612 and G3616 Engines Vibration Damper - Install
3126B Engines for Caterpillar Built Machines Crankshaft - Install
G3612 and G3616 Engines Vibration Damper - Remove
C-9 Engines for Caterpillar Built Machines Valve Mechanism Cover
G3612 and G3616 Engines Vibration Damper - Install
3126B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3406E Truck Engines BrakeSaver Troubleshooting
3126B and 3126E On-highway Engines Crankshaft Main Bearings - Install