Crankshaft Main Bearings - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 2P-5518 | Main Bearing Tool | 1 |
B | 6V-4876 | Lubricant | 1 |
C | 8T-5096 | Dial Indicator Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. Ensure that the tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main bearing caps and the cylinder block.
- Use Tooling (A) and install the upper halves of the crankshaft main bearings in the cylinder block. Do not put oil on the back of the crankshaft main bearing.
Show/hide table
Illustration 2 g00988316 - Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2). Do not put oil on the back of the crankshaft main bearing.
Show/hide table
NOTICE Crankshaft main bearing caps should be installed with the part number toward the right side of the engine. Crankshaft main bearing caps are to be identified by stamped numbers 1 through 7 located on the bottom surface. The thrust plate is used on the number 6 crankshaft main bearing only.
- Position crankshaft main bearing caps (2) on the cylinder block. Apply Tooling (B) on the bolt threads and on the washer face. Install bolts (1).
- Tighten bolts (1) to a torque of
54 ± 7 N·m (40 ± 5 lb ft) . Tighten each bolt (1) for an additional 90 ± 5 degrees (1/4 turn). - Check the end play of the crankshaft with Tooling (C). The end play must be
0.07 to 0.32 mm (0.003 to 0.013 inch) .
Show/hide table
Illustration 1 | g00988318 |
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
3406E Truck Engines BrakeSaver Troubleshooting
3126B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
G3612 and G3616 Engines Vibration Damper - Install
C-9 Engines for Caterpillar Built Machines Valve Mechanism Cover
G3612 and G3616 Engines Vibration Damper - Remove
3126B Engines for Caterpillar Built Machines Crankshaft - Install
G3612 and G3616 Engines Vibration Damper - Install
3126B Engines for Caterpillar Built Machines Crankshaft - Remove
SR4B Generators Generator Operation
3126 Truck Engine Military Air Compressor Drive Gear - Install
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
G3612 and G3616 Engines Vibration Damper - Remove
G3612 and G3616 Engines Vibration Damper - Disassemble
3114, 3116, and 3126 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3406E Truck Engine BrakeSaver Pull-Down RPM Check
3406E Truck Engine BrakeSaver Klunk Check (Free Movement of the Valve Spool)
3406E Truck Engine BrakeSaver Troubleshooting Problem List
3034 Industrial Engine Engine Description
C-9 Engines for Caterpillar Built Machines Gear Group (Front)
3126 Truck Engine Military Pistons and Connecting Rods - Remove
G3612 and G3616 Engines Vibration Damper - Assemble
3114, 3116, and 3126 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Truck Engine Pistons and Connecting Rods - Disassemble
3034 Engine for Caterpillar Built Machines Crankcase Breather - Remove and Install