Vibration Damper - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8T-0914 | 导向销 | 2 |
B | 1U-9392 | 减振器导向销 | 2 |
C | 4C-5590 | 防粘结剂 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将工具 (A) 安装在曲轴中。
- 将隔套 (5) 置于工具 (A) 上。 确保将适配器组件固定在一起的螺栓头与隔套 (5) 中的孔配合紧密。
Show/hide table
图 2 g01294025 - 通过减振器 (4) 的中央安装一个合适的起吊设备。 窄减振器的重量约为
288 kg (639 lb) 。 宽减振器的重量约为402 kg (882 lb) 。 - 将减振器 (4) 上的上止点位置的正时标记和曲轴上的正时标记对齐。 确保对准了螺栓孔。 将减振器 (4) 置于工具 (A) 上。 务必使减震器中央的小螺栓头与隔套配合紧密。 安装减振器 (4)。
Show/hide table
图 3 g01294011 - 在工具 (A) 上安装接头 (3)。 确保对准了螺栓孔。 务必使减震器 (4) 中央的小螺栓头与隔套 (3) 配合紧密。
- 将工具 (C) 涂抹到螺栓螺纹上,以穿过适配器 (3) 和减振器 (4) 并固定到曲轴上。
- 安装穿过适配器 (3) 和减振器 (4) 的螺栓并固定到曲轴上。 按对角线顺序拧紧螺栓至扭矩为
1350 ± 150 N·m (1000 ± 110 lb ft) 。 - 拆下工具 (A),并在接头 (3) 中安装工具 (B)。
注: 确保以正确的方向安装外部减振器。 应将上止点位置正时标记以顺时针方向从减振器 (4) 上的上止点位置正时标记转动 36 度。 当从发动机前部查看减振器时,决定方向。
Show/hide table图 4 g00609906 Show/hide table图 5 g00609902 此图为双重减振器的图示。 - 通过减振器 (2) 的中央安装一个合适的起吊设备。 窄减振器的重量约为
288 kg (639 lb) 。 宽减振器的重量约为402 kg (886 lb) 。 - 安装减振器 (2)。 确保将振动器中的螺栓孔与接口中的螺纹孔对齐。 确保使减震器 (2) 中央的小螺栓头与隔套配合紧密。
- 将工具 (C) 涂敷在螺栓 (1) 的螺纹上。
- 安装将减振器 (2) 固定在接头上的螺栓 (1)。 拆下工具 (B)。 安装其余的螺栓 (1)。 按对角线顺序拧紧螺栓至扭矩为
1350 ± 150 N·m (1000 ± 110 lb ft) 。
Show/hide table
图 1 | g00609918 |
结束:
- 安装减振器护罩总成。
Caterpillar Information System:
3126B Engines for Caterpillar Built Machines Crankshaft - Remove
SR4B Generators Generator Operation
3126 Truck Engine Military Air Compressor Drive Gear - Install
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
G3612 and G3616 Engines Vibration Damper - Remove
G3612 and G3616 Engines Priority Valve - Assemble
G3612 and G3616 Engines Priority Valve - Disassemble
G3612 and G3616 Engines Priority Valve - Install
3126B and 3126E On-highway Engines Air Compressor - Remove and Install
3126B and 3126E On-highway Engines Fan Drive - Install
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Remove
3126B Engines for Caterpillar Built Machines Crankshaft - Install
G3612 and G3616 Engines Vibration Damper - Remove
C-9 Engines for Caterpillar Built Machines Valve Mechanism Cover
G3612 and G3616 Engines Vibration Damper - Install
3126B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3406E Truck Engines BrakeSaver Troubleshooting
3126B and 3126E On-highway Engines Crankshaft Main Bearings - Install
G3612 and G3616 Engines Vibration Damper - Disassemble
3114, 3116, and 3126 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3406E Truck Engine BrakeSaver Pull-Down RPM Check
3406E Truck Engine BrakeSaver Klunk Check (Free Movement of the Valve Spool)
3406E Truck Engine BrakeSaver Troubleshooting Problem List