Vibration Damper - Disassemble
开始:
- 拆卸减振器。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7573 | 连杆支架 | 3 |
Show/hide table
将硅注入减振器。 该材质很厚,必须使用油灰刮刀清除。 请戴上手套,以免刺激皮肤。 |
- 将减振器放平。 注油塞 (1) 必须正面朝上。
- 卸下注油塞 (1),然后将减振器在室温下放置 8 个小时。
Show/hide table
图 2 g00610185 此图为窄减振器的图示。 - 卸下将盖 (2) 固定至轮毂 ( 3) 和环 (4) 上的螺栓。 拆下外盖。
Show/hide table
图 3 g00610188 - 卸下轴承 (5)。
Show/hide table
图 4 g00610192 - 将工具 (A)和起重机固定至配重块 ( 6)。 窄减振器上 (6) 的配重块的重量约为
169 kg (376 lb) 。 宽减振器上 (6) 的配重块的重量约为341 kg (747 lb) 。 - 卸下轴承 (7)。
Show/hide table
图 5 g00610198 - 卸下 O 形密封圈 (8),然后卸下其他 O 形密封圈 (9)。
Show/hide table
图 6 g00610208 - 将轮毂 (3) 和环 ( 4) 翻转放置在硬纸板上。
- 卸下将盖 (10) 固定至轮毂 ( 3) 的螺栓。 将盖 (10 ) 和环 (4) 从轮毂 ( 3) 上提起。
Show/hide table
图 7 g00610210 - 从环 (4) 上卸下盖 ( 10)。 拆下 O 形密封圈。
- 卸下 O 形密封圈 (11 )。
- 彻底清洁所有的零件。 检查部件是否磨损或损坏。
Show/hide table
图 1 | g00610184 |
Caterpillar Information System:
3126B and 3126E On-highway Engines Crankshaft Main Bearings - Install
3406E Truck Engines BrakeSaver Troubleshooting
3126B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
G3612 and G3616 Engines Vibration Damper - Install
C-9 Engines for Caterpillar Built Machines Valve Mechanism Cover
G3612 and G3616 Engines Vibration Damper - Remove
3126B Engines for Caterpillar Built Machines Crankshaft - Install
G3612 and G3616 Engines Vibration Damper - Install
3126B Engines for Caterpillar Built Machines Crankshaft - Remove
SR4B Generators Generator Operation
3126 Truck Engine Military Air Compressor Drive Gear - Install
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
3114, 3116, and 3126 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3406E Truck Engine BrakeSaver Pull-Down RPM Check
3406E Truck Engine BrakeSaver Klunk Check (Free Movement of the Valve Spool)
3406E Truck Engine BrakeSaver Troubleshooting Problem List
3034 Industrial Engine Engine Description
C-9 Engines for Caterpillar Built Machines Gear Group (Front)
3126 Truck Engine Military Pistons and Connecting Rods - Remove
G3612 and G3616 Engines Vibration Damper - Assemble
3114, 3116, and 3126 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Truck Engine Pistons and Connecting Rods - Disassemble
3034 Engine for Caterpillar Built Machines Crankcase Breather - Remove and Install
3126 Truck Engine Military Pistons and Connecting Rods - Assemble