Oil Temperature Regulators - Remove and Install
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 断开所有电气连接。
- 卸下将盖 (3) 固定至机油温度调节器壳体 ( 2) 的十个螺栓 (1)。
- 卸下以下部件: 盖 (3), 垫片 和 管 (4) 。 检查密封垫有无磨损或损坏。 必要时,更换密封垫。
Show/hide table
图 2 g00869884 - 从机油温度调节器壳体 ( 2) 上卸下机油温度调节器 ( 5)。
- 从机油温度调节器壳体上卸下唇型密封。
Show/hide table
图 1 | g00869866 |
注: 要卸下机油温度调节器,不必从发动机上卸下机油温度调节器壳体 ( 2)。
注: 电气连接以及模式的其他变更可能要求在更换部件之前进行更多的拆卸或断开。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-0510 | 起子总成 | 1 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A)。 将唇型密封安装在壳体 ( 2) 中。 密封唇必须背对着盖 ( 3)。
- 将机油温度调节器 ( 5) 安装在机油温度调节器壳体中。
Show/hide table
图 4 g00869866 - 将新 O 型密封圈安装在管 ( 4) 上。 在 O 形密封圈上涂抹清洁的发动机机油。
- 将管 (4) , 垫片 和 盖 (3) 放置在机油温度调节器壳体上。
- 安装螺栓 (1)。
- 连接所有电气连接。
Show/hide table
图 3 | g00869884 |
结束:
- 检查发动机中的机油油位。 请参阅操作和维护手册。
Caterpillar Information System:
3126B and 3126E On-highway Engines Engine Control Module - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Assemble
G3612 and G3616 Engines Engine Oil Pan - Disassemble
3126B and 3126E On-highway Engines Alternator - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Install
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
C-9 Engines for Caterpillar Built Machines Engine Design
G3612 and G3616 Engines Engine Oil Pan - Remove
3126B Truck Engine Electronic Control System Components
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3612 and 3616 Engines Aftercooler - Remove - High Performance Aftercooler
3126B and 3126E On-highway Engines Fan Drive - Remove
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Install
3126B and 3126E On-highway Engines Air Compressor - Remove and Install
G3612 and G3616 Engines Priority Valve - Install
G3612 and G3616 Engines Priority Valve - Disassemble
G3612 and G3616 Engines Priority Valve - Assemble
G3612 and G3616 Engines Vibration Damper - Remove
3126B and 3126E On-highway Engines Air Compressor Drive Gear - Remove and Install
3126 Truck Engine Military Air Compressor Drive Gear - Install
SR4B Generators Generator Operation