Engine Oil Pan - Remove
开始:
- 切断供油,然后断开供油管。
- 移开膨胀箱,然后断开供水管。
- 断开通向空气起动马达的供气管。 断开通向安装硬件及空气起动马达的供气管。
- 取下空气滤清器。
- 切断排气系统。
- 断开发电机联轴器。
- 断开预润滑泵。
- 切断供电。
- 从油底壳排出机油。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 卸下将管组件固定至油底壳(如有配备)的螺栓和卡箍。
- 卸下四个螺栓和垫片 ( 1)。 从油底壳及机油泵上卸下管组件 ( 2)。
- 确保缸体与油底壳之间无连接。
- 安装发动机提升支架。 请参阅拆解和装配发动机提升支架 , "- 拆卸和安装" 。 将起重机连接至发动机提升支架。 卸下将发动机及支架固定至底座的所有螺栓。
注: 从底座上提升发动机之前,先检查是否仍有其它部件连接在发动机上。
- 将发动机从底座上拆下。 12 缸发动机的重量约为
24 084 kg (55,300 lb) 。 16 缸发动机的重量约为29 892 kg (65,900 lb) 。注: 该值仅为发动机本身的重量。
- 将发动机放置于台架上。 为便于拆卸油底壳,台架的高度最小为
671 mm (26.4 inch) 。Show/hide table图 2 g00553586 此图为典型的安装图示。 - 将托盘式千斤顶放置于油底壳 ( 4) 各端的下方。 12 缸发动机中的油底壳重量为
622 kg (1382 lb) 。 16 缸发动机中的油底壳重量为661 kg (1457 lb) 。 - 升起托盘式千斤顶,以支撑油底壳。
- 卸下螺栓 (3)。
- 将油底壳移至适当的工作区。
Show/hide table
图 3 g00553587 此图为典型的安装图示。 - 从油底壳 (4) 上卸下垫片 ( 5)。
Show/hide table
图 1 | g00609460 |
Caterpillar Information System:
3126B Truck Engine Electronic Control System Components
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3406E Generator Set Engines Annunciator Panel - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Assemble
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Disassemble
C15 Petroleum Generator Set Engines Flywheel - Inspect
3114, 3116 and 3126 Engines Unit Injector Cranking Rack Position
C15 Petroleum Generator Set Engines Cylinder Liner Projection - Inspect
3126B Truck Engine Glossary of Electronic Control Terms
C-9 Engines for Caterpillar Built Machines Engine Design
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
G3612 and G3616 Engines Engine Oil Pan - Install
3126B and 3126E On-highway Engines Alternator - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Disassemble
G3612 and G3616 Engines Engine Oil Pan - Assemble
3126B and 3126E On-highway Engines Engine Control Module - Remove and Install
G3612 and G3616 Engines Oil Temperature Regulators - Remove and Install
3612 and 3616 Engines Aftercooler - Remove - High Performance Aftercooler
3126B and 3126E On-highway Engines Fan Drive - Remove
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Install