Engine Oil Pan - Install
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 清洁油底壳上的垫片表面和缸体。 将新的油底壳垫片 (5) 安装在油底壳上 (4)。
注: 检查油底壳内部,确保已卸下所有外物。 同时检查抽吸管。
Show/hide table图 2 g00553586 此图为典型的安装图示。 - 将油底壳 (4) 移至缸体下方的合适位置上。
- 在油底壳的拐角处安装若干半英寸的导销。 升起油底壳至合适高度,然后安装螺栓 (3) 和垫圈。
Show/hide table
图 3 g00609460 - 将管组件和垫片 (1) 放置在合适位置上。 安装四个螺栓。 将管组件 (2) 安装在油底壳与机油泵之间。
注: 安装前用清洁的发动机机油润滑 O 形密封圈。
- 安装卡箍和将管组件(如有配备)固定至油底壳的螺栓。
- 从台架上卸下发动机,然后将发动机安装在底座上。
- 连接电源。
- 连接预润滑泵。
- 连接发电机联轴器。
- 连接排气系统。
- 连接空气滤清器。
- 将供气管连接至空气起动马达。 将供气管连接至安装硬件及空气起动马达的管路上。
- 将膨胀水箱和水管连接。
- 连接供油管,接通供油。
- 向发动机加注机油到正确的油位。 请参阅操作和维护手册。
- 将水系统注水至正确的水位。 请参阅操作和维护手册。
Show/hide table
图 1 | g00553587 |
此图为典型的安装图示。 |
结束:
- 起动发动机前,预润滑发动机。
Caterpillar Information System:
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
C-9 Engines for Caterpillar Built Machines Engine Design
G3612 and G3616 Engines Engine Oil Pan - Remove
3126B Truck Engine Electronic Control System Components
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3406E Generator Set Engines Annunciator Panel - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Assemble
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Disassemble
C15 Petroleum Generator Set Engines Flywheel - Inspect
3126B and 3126E On-highway Engines Alternator - Remove and Install
G3612 and G3616 Engines Engine Oil Pan - Disassemble
G3612 and G3616 Engines Engine Oil Pan - Assemble
3126B and 3126E On-highway Engines Engine Control Module - Remove and Install
G3612 and G3616 Engines Oil Temperature Regulators - Remove and Install
3612 and 3616 Engines Aftercooler - Remove - High Performance Aftercooler
3126B and 3126E On-highway Engines Fan Drive - Remove
G3612 and G3616 Engines Priority Valve - Remove
3126B and 3126E On-highway Engines Fan Drive - Install
3126B and 3126E On-highway Engines Air Compressor - Remove and Install
G3612 and G3616 Engines Priority Valve - Install
G3612 and G3616 Engines Priority Valve - Disassemble