Hydraulic Oil Cooler - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7574 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Check the condition of the hydraulic oil cooler prior to installation. Remove any dirt or debris that may restrict the flow of air through the core. If any of the cooling fins are bent, the fins should be straightened prior to the installation of the hydraulic oil cooler.
- Fasten Tooling (A) to hydraulic oil cooler (5). Fasten a suitable lifting device to Tooling (A) .
Show/hide table
 | |
| Illustration 1 | g00363734 |
- Carefully position hydraulic oil cooler (5) . The weight of the hydraulic oil cooler is 68 kg (150 lb).
- Install the four washers and four bolts (3) that hold hydraulic oil cooler (5) in position.
Show/hide table
 | |
| Illustration 2 | g00363733 |
- Check the condition of the O-ring seals in the ends of hose assemblies (4). If the O-ring seals are broken or damaged, use a new part for replacement.
- Connect two hose assemblies (4) .
- Position refrigerant condenser (2) .
Show/hide table
 | |
| Illustration 3 | g00363712 |
- Install the four washers and four bolts (1) .
- Remove the ecology drain valve from the hydraulic oil tank. Fill the hydraulic oil tank to the correct level. Refer to Operation and Maintenance Manual for the correct procedure to fill the hydraulic oil tank.
End By: Install the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install" in this manual.
Caterpillar Information System:
315B Excavator Machine Systems Swing Drive - Assemble
315B Excavator Machine Systems Fuel Tank - Remove
315B Excavator Machine Systems Counterweight - Remove and Install
M318 and M320 Excavators Machine System Specifications Control Valve (Boom Lowering)
330B Excavator Hydraulic System Pump Control (Negative Flow) - Adjust
315B Excavator Machine Systems Boom - Install
M322C Wheeled Excavator Machine System Swing Gear and Bearing
M315 Excavator Machine System Stick - 1.7 m (5.58 ft)
M318 and M320 Excavators Machine System Specifications Travel Motor
Installation of the Two-Way Pilot Valve (Control Pattern Change) {5059, 5496} Installation of the Two-Way Pilot Valve (Control Pattern Change) {5059, 5496}
330B Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
315B Excavator Machine Systems Swing Drive - Disassemble
320B, 320B L and 320B N Excavators Work Tool Flow Control - If Equipped
M315 Excavator Machine System Stick - 2.1 m (6.89 ft)
M315 Excavator Machine System Stick - 2.4 m (7.87 ft)
M315 Excavator Machine System Stick - 2.6 m (8.53 ft)
M315 Excavator Machine System Stick - 3.1 m (10.17 ft)
5130B Excavator Hydraulic System Relief Valve (Margin)
315B Excavator Machine Systems Undercarriage Frame - Remove
315B Excavator Machine Systems Fuel Tank - Install
5230 Excavator Hydraulic System Hydraulic System Troubleshooting
315B Excavator Machine Systems Seat - Remove and Install
315B and 315B L Excavator Supplement For 3046 Engine Radiator - Remove
M315 Excavator Machine System Bucket Cylinder