Engine Oil and Filter - Change
Show/hide table
熱機油和高溫組件會導致人員受傷。 請勿讓熱油接觸到皮膚。 |
Show/hide table
注意事項 |
---|
在檢驗、保養、測試、調整及修理機器時,請小心確保油液有容器盛裝。 在打開任何艙室或拆卸任何含有用液的組件前,應準備好盛裝用液的適當容器。 請參閱專門出版物, NENG2500, "Caterpillar 工具和車間產品指南",瞭解適用於收集與盛裝液體的工具及用品。 按照當地的條例和法規棄置廢棄的油液。 |
- 打開下部引擎檢修門。
Show/hide table
插圖 1 g06133525 - 打開曲軸箱排放閥。 將機油排放到合適的容器內。 關閉曲軸箱排放閥。
- 打開駕駛員控制台下方的檢修門。
Show/hide table
插圖 2 g06133527 - 拆下濾清器濾芯。 丟棄濾清器濾芯。
- 清潔濾清器外殼基座。 所有舊濾清器密封圈皆需自濾清器底座上移除。
Show/hide table
插圖 3 g03434945 - 在新濾清器濾芯的密封件上塗上薄薄一層乾淨的引擎機油。
- 裝上引擎機油濾清器並用手鎖緊,直到引擎機油濾清器的密封件接觸到濾清器底座為止。 請注意,濾清器上的指示標記的位置與濾清器基座上的固定點相關。
附註每個引擎機油濾清器上的各個旋轉指示標記之間相隔 90 度,或是整個圓的 1/4。 您在擰緊引擎機油濾清器時,應參考旋轉指示標記。
- 根據濾清器上的說明擰緊濾清器。 請使用指示標記作為指導。
附註您可能需要使用 Caterpillar 帶式扳手或其他適當工具,以便將濾清器轉至最後安裝位置所需的轉動量。 確保安裝工具不會損壞濾清器。
- 升起引擎室的機蓋。
Show/hide table
注意事項 請勿過度加注曲軸箱。 否則引擎可能損壞。
Show/hide table插圖 4 g06133516 - 取下注油塞 (1)。 將新的機油注入曲軸箱。 清潔注油塞,然後裝上注油塞。
- 起動引擎,讓機油循環。 檢查是否有洩漏。
- 關閉引擎。
- 使用機油液位表 (2) 檢查引擎機油油位。
- 蓋上引擎蓋。
Caterpillar Information System:
PM310, PM312, and PM313 Cold Planer Engine Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Engine Oil Level - Check
PM310, PM312, and PM313 Cold Planer Engine Mounts - Inspect
PM310, PM312, and PM313 Cold Planer Engine Air Filter Primary Element - Clean/Replace
PM310, PM312, and PM313 Cold Planer Diesel Exhaust Fluid Filter - Replace
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Simple Calibration
PM310, PM312, and PM313 Cold Planer Diesel Exhaust Fluid - Fill
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Sample (Level 2) - Obtain
PM310, PM312, and PM313 Cold Planer Coolant Sample (Level 1) - Obtain
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Level - Check
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Extender (ELC) - Add
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Powered Stairway - Check
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine Oil Cooler - Remove and Install
PM310, PM312, and PM313 Cold Planer Fuel Tank Water and Sediment - Drain
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil - Change
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Filter - Replace
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Level - Check
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Legs (Struts) - Lubricate
785G Off-Highway Truck Systems Electronic Control Module (ECM) - Replace
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Editing Truck and Material Lists
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
797F and 797F XQ Off-Highway Trucks Magnetic Plug (Pump Drive, Hydraulic) - Check
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge