Coolant Sample (Level 1) - Obtain
附註如果冷卻系統已加滿 Cat ELC (長效冷卻液),就不需要取得冷卻液樣本 (1 級)。 裝滿了 Cat ELC 的冷卻系統應該按照保養週期表中說明的建議週期,採集用於 2 級分析的冷卻液樣本。
附註如果冷卻系統加注了 Cat ELC 以外的任何其他冷卻液,則應該採集用於 1 級分析的冷卻液樣本。 這包括以下類型的冷卻液。
- 符合 Caterpillar 引擎冷卻液規格 -1 (Caterpillar EC-1) 的市售長效冷卻液
- Cat 柴油引擎防凍劑/冷卻液 (DEAC)
- 市售重載型冷卻液/防凍劑
附註1 級的分析結果可能表示需要進行 2 級分析。
Show/hide table
注意事項 |
---|
在檢驗、保養、測試、調整及修理產品時,請小心確保油液有容器盛裝。 在打開任何艙室或拆卸任何含有用液的組件前,應準備好盛裝用液的適當容器。 請參閱特別出版品, N4NG2500, "代理商維修工具目錄",以瞭解適合用來收集及容納 Cat® 產品之液體的工具和耗材。 按照當地的條例和法規棄置廢棄的油液。 |
盡可能在接近建議的取樣週期時提取冷卻液樣本。 1 級冷卻液分析的建議取樣週期為每 500 工時。 若要獲得 S·O·S 分析的完整效應,必須建立一致的資料趨向。 若要建立資料的相關記錄,請持續按照平均的時間間隔執行取樣。 您可以向 Caterpillar 代理商索取收集樣本的用品。
使用以下指南進行正確的冷卻液取樣:
- 取樣前,請填寫取樣瓶標籤上的資訊。
- 將未使用的取樣瓶存放在塑膠袋中。
- 請將空的樣本瓶保持蓋緊,直到您準備收集樣本。
- 提取樣本後,請立即將其放到郵寄管中,以避免污染。
- 切勿從膨脹瓶中收集樣本。
- 切勿從系統排放物中收集樣本。
Show/hide table
插圖 1 | g06134553 |
引擎冷卻液的 S O S 開口位於冷卻液泵附近。 打開駕駛員平台上的引擎檢修門,即可看見該開口。
機器必須運作才能使冷卻液循環。 請在正常工作天結束時收集樣本。 請在引擎關閉 1 至 2 小時後收集樣本。
Caterpillar Information System:
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Level - Check
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Extender (ELC) - Add
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Powered Stairway - Check
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Hoist Screens - Clean
440 and 450 Backhoe Loader Hydraulic Coupling Quick Disconnect - Clean/Inspect
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Locks - Lubricate
730C2 and 725C2 Articulated Truck Power Train Center Axle - Remove and Install
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Cooling System Coolant (ELC) - Change
Procedure to Install an Improved Clean Fuel Module Relay on Certain 793F, 795F, and 797F Large Off-Highway Trucks {1408, 1417, 1422, 4493} Procedure to Install an Improved Clean Fuel Module Relay on Certain 793F, 795F, and 797F Large Off-Highway Trucks {1408, 1417, 1422, 4493}
C175-16 and C175-20 Engines for Off-Highway Truck/Tractors Exhaust Has Excessive White Smoke
2570D and 2670D Wheel Feller Buncher Engine Supplement Aftercooler - Remove and Install
2570D and 2670D Wheel Feller Buncher Engine Supplement Hydraulic Oil Cooler - Remove and Install
PM310, PM312, and PM313 Cold Planer Cooling System Coolant Sample (Level 2) - Obtain
PM310, PM312, and PM313 Cold Planer Diesel Exhaust Fluid - Fill
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Simple Calibration
PM310, PM312, and PM313 Cold Planer Diesel Exhaust Fluid Filter - Replace
PM310, PM312, and PM313 Cold Planer Engine Air Filter Primary Element - Clean/Replace
PM310, PM312, and PM313 Cold Planer Engine Mounts - Inspect
PM310, PM312, and PM313 Cold Planer Engine Oil Level - Check
PM310, PM312, and PM313 Cold Planer Engine Oil Sample - Obtain
PM310, PM312, and PM313 Cold Planer Engine Oil and Filter - Change
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine Oil Cooler - Remove and Install
PM310, PM312, and PM313 Cold Planer Fuel Tank Water and Sediment - Drain
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil - Change