Temperature Sensor (DPF) - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | Loctite Nickel Anti-Seize Thread Compound | 1 | |
Start By:
- Connect the steering frame lock.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Raise hood (1) by activating switch (2). Turn battery disconnect switch (3) to the OFF position.
Show/hide table
Illustration 2 g03348327 - Remove clips (4), bolt (6), and hose (5).
Show/hide table
Illustration 3 g03348368 - Remove bolts (8). Remove four bolts (9) (two not shown). Remove upper shroud (7).
Show/hide table
Illustration 4 g03350541 Show/hide table
Illustration 5 g03350544 - Remove temperature sensor (10). Cut cable straps (11).
Show/hide table
Illustration 6 g03350551 - Remove the other end of temperature sensor (10).
Show/hide table
| |
| Illustration 1 | g03330059 |
- Install temperature sensors (10) in the reverse order of removal.
- Apply Tooling (A) to the threads of temperature sensors (10).
- Tighten temperature sensors (10) to a torque of
45 ± 5 N·m (33 ± 4 lb ft) .
Caterpillar Information System:
24M Motor Grader Hydraulic and Steering System Introduction
R1300G Load Haul Dump 3306 Engine Supplement Governor Actuator - Remove and Install
2013/03/22 A New Universal Joint is Now Used on Certain Large Off-Highway Trucks {3108, 3251}
2013/03/01 New TOPCON Grade Controller Software Is Now Available For Certain Asphalt Pavers {7219, 7220, 7620}
2013/03/08 The Enclosure Latch Assembly Has Been Improved on Certain 24M Motor Graders {7263}
2013/04/25 Improved Coolant Gasket Used on Certain 3500 Engines {1353, 1380, 7555}
730C2 Articulated Truck Stopping the Engine
Installation of the 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers{7324} Installation of the 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers{7324}
2013/02/22 An Improved Oil Line Support Bracket Is Now Available On Certain Off-Highway Trucks, Wheel Loaders, and Wheel Dozers. {1307}
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Undercarriage - Remove and Install
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Electrical Connector - Inspect
814K, 816K, 826K 836K Landfill Compactors, 815K, 825K, Soil Compactors, 824K, 834K, 844K, 854K Wheel Dozers and 986K, 988K, 990K, 992K,994K Wheel Loaders Information Display Configuration Menu
2013/03/04 Improved Installation of the Multifunctional Lever Harness As on Certain Off-Highway Trucks and Wheel Tractor-Scrapers {1408, 5737}
24M Motor Grader Hydraulic and Steering System Location of Components
2570C and 2670C Wheel Feller Bunchers Capacities (Refill)
24M Motor Grader Hydraulic and Steering System Control Manifold (Implement, Steering)
725C2 Articulated Truck Additional Messages
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Ignition Coil - Remove and Install
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Exhaust Lines - Remove and Install
Procedure to Install the Alarm Group on Certain Off-Highway Trucks {1408, 7301} Procedure to Install the Alarm Group on Certain Off-Highway Trucks {1408, 7301}
986H Wheel Loader Machine Systems Transmission Oil Pump
2570C and 2670C Wheel Feller Bunchers Windows - Clean
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Track Drive - Remove and Install
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Chain (Drive) - Remove and Install