Undercarriage - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 180-3033 | 千斤顶台架总成 | 4 |
B | 1U-9200 | 操纵杆滚轮举倾机构 | 1 |
C | 292-3840 | 拆卸工具组件 | 2 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 把机器停放在坚固水平的场地上。
- 撤去安装在快速接头上的任何作业机具。
- 提升装载机臂,为装载机提升臂安装支架。 请参阅操作和保养手册, "装载机起吊臂支架的操作"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
Show/hide table
图 1 g01338128 - 举升机器,直到底盘系统 (1) 上的履带和尺寸 (X) 离开地面大约
50 mm (2.0 inch) 。 将工具 (A) 安置在机器下面。Show/hide table图 2 g01338587 - 拆下螺栓 (3) 和垫圈。
- 拆下螺栓 (4) 和垫圈。
- 拆下盖组件 (2) 和垫圈 (5)(未显示)。
Show/hide table
图 3 g03350237 - 拆下螺栓 (6) 和垫圈。 拆下隔套 (7)。
Show/hide table
图 4 g03394230 - 将适当的起吊设备和工具 (B) 连接到底盘系统 (1)。 底盘系统 (1) 的重量约为
635 kg (1400 lb) 。Show/hide table图 5 g01338516 Show/hide table图 6 g01338525 - 将工具 (C) 连接到底盘系统 (1)。 使用工具 (C) 将底盘系统 (1) 从机器上移开足够的距离,以便接近软管组件。
- 断开软管组件 (8)。
- 断开软管组件 (9)。
- 断开软管组件 (10)。
- 断开线束组件 (11)。
- 利用工具 (C)、工具 (B) 和适当的起吊设备将底盘系统 (1) 从机器上拆下。
Show/hide table
图 7 g01338838 - 拆下隔套 (12)。
Show/hide table
图 8 g01338893 - 拆下垫圈 (13)。
- 按与拆卸相反的顺序安装底盘系统 (1)。
Caterpillar Information System:
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Electrical Connector - Inspect
814K, 816K, 826K 836K Landfill Compactors, 815K, 825K, Soil Compactors, 824K, 834K, 844K, 854K Wheel Dozers and 986K, 988K, 990K, 992K,994K Wheel Loaders Information Display Configuration Menu
986H Wheel Loader Machine Systems General Information (Brake, Hydraulic Fan System)
MH3049 Material Handler Machine Systems Cab Riser Cylinder - Remove and Install - Forward/Back Cylinders
2570C and 2670C Wheel Feller Bunchers Parking Brake Manual Release
2013/03/01 Improved Bolts Now Used on Bunching Finger and Grapple Arm Cylinder Glands on Felling Heads {5362, 5555, 6307}
14M Series 3 Motor Grader Maintenance Interval Schedule
2013/03/18 Improved 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers {7324}
C1.5 and C2.2 Engines for Caterpillar Built Machines Air in Fuel - Test
2013/03/04 New Governor Actuator Adjustment Procedure Now Used on R1300G Load Haul Dump Machines {1265, 1716}
Installation and Configuration of Cat® Terrain v5.0 On-board Software{7605} Installation and Configuration of Cat® Terrain v5.0 On-board Software{7605}
Installation of 359-3176 Pivot Bearing and the 433-6434 Plate Assembly on Certain Vibratory Asphalt Compactors{7253} Installation of 359-3176 Pivot Bearing and the 433-6434 Plate Assembly on Certain Vibratory Asphalt Compactors{7253}
2013/02/22 An Improved Oil Line Support Bracket Is Now Available On Certain Off-Highway Trucks, Wheel Loaders, and Wheel Dozers. {1307}
Installation of the 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers{7324} Installation of the 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers{7324}
730C2 Articulated Truck Stopping the Engine
2013/04/25 Improved Coolant Gasket Used on Certain 3500 Engines {1353, 1380, 7555}
2013/03/08 The Enclosure Latch Assembly Has Been Improved on Certain 24M Motor Graders {7263}
2013/03/01 New TOPCON Grade Controller Software Is Now Available For Certain Asphalt Pavers {7219, 7220, 7620}
2013/03/22 A New Universal Joint is Now Used on Certain Large Off-Highway Trucks {3108, 3251}
R1300G Load Haul Dump 3306 Engine Supplement Governor Actuator - Remove and Install
24M Motor Grader Hydraulic and Steering System Introduction
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Temperature Sensor (DPF) - Remove and Install
2013/03/04 Improved Installation of the Multifunctional Lever Harness As on Certain Off-Highway Trucks and Wheel Tractor-Scrapers {1408, 5737}
24M Motor Grader Hydraulic and Steering System Location of Components