Installation of the 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers{7324}
- Wheel Feller Buncher:
- 2470C (S/N: W2M1-UP)
- 2570C (S/N: F1B1-UP)
- 2670C (S/N: B3E1-UP)
- 553C (S/N: PGR1-UP)
- 563C (S/N: JCB1-UP)
- 573C (S/N: RJT1-UP)
- 2570C (S/N: F1B1-UP)
Introduction
This Special Instruction provides information for installation of the 431-5438 Shaft Kit .
Do not perform any procedure that is outlined in this publication, or order any parts until you understand this information.
Parts Required
Show/hide table
Part     | Part No.     | Description     | Qty     |
---|---|---|---|
1     | 431-5438     | Shaft Kit     | 1     |
Removal Procedure
- Remove 387-9474 Lock Knob (1) from the arm rest/joystick assembly.
Show/hide table
Illustration 1 | g03351420 |
- Remove arm rest/joystick assembly and place the assembly out of the way.
- Remove 391-7138 Gas Spring (2).
Show/hide table
Illustration 2 | g03351439 |
- Remove pivot shaft retainer clip (3) .
Show/hide table
Illustration 3 | g03351459 |
- Remove hose guide (4) from pivot shaft (5) .
- Remove pivot shaft by cutting the weld on the back side of shaft (5) .
Ensure the Following Before Proceeding to the Installation Procedure
- Ensure that the back surface of the hanger is smooth and free of any excess weld. Ensure that the flat washer will lay flat and not contact any existing weld during reassembly.
Note: If any weld is present, make sure to cover the seat and grind smooth.
- Ensure the hole where the shaft used to be allows a 5/8 bolt to pass through.
Note: If the bolt will not pass through, drill out the hole.
Installation Procedure
Show/hide table
Illustration 4 | g03351676 |
- Remove the existing flanged bushing from the inside of the hose guide and replace with item (3) from the kit.
- Apply Loctite to the last 3/4 of the threads of item (1) .
- Assemble with washers (2) as shown.
- Install nut (4) and tighten.
Note: When tightening, make sure not to over tighten to the point that hose guide (5) will not pivot.
- Verify that when the hose guide pivots down it properly contacts the headed stop pin (6) .
- Install arm rest/joystick assembly.
- Install 387-9474 Lock Knob (1) into arm rest/joystick assembly and adjust/ tighten to correct operator adjustment.
Caterpillar Information System:
2013/02/22 An Improved Oil Line Support Bracket Is Now Available On Certain Off-Highway Trucks, Wheel Loaders, and Wheel Dozers. {1307}
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Undercarriage - Remove and Install
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Electrical Connector - Inspect
814K, 816K, 826K 836K Landfill Compactors, 815K, 825K, Soil Compactors, 824K, 834K, 844K, 854K Wheel Dozers and 986K, 988K, 990K, 992K,994K Wheel Loaders Information Display Configuration Menu
986H Wheel Loader Machine Systems General Information (Brake, Hydraulic Fan System)
MH3049 Material Handler Machine Systems Cab Riser Cylinder - Remove and Install - Forward/Back Cylinders
2570C and 2670C Wheel Feller Bunchers Parking Brake Manual Release
2013/03/01 Improved Bolts Now Used on Bunching Finger and Grapple Arm Cylinder Glands on Felling Heads {5362, 5555, 6307}
14M Series 3 Motor Grader Maintenance Interval Schedule
2013/03/18 Improved 431-5438 Shaft Kit for the Armrest on Certain Wheel Feller Bunchers {7324}
C1.5 and C2.2 Engines for Caterpillar Built Machines Air in Fuel - Test
2013/03/04 New Governor Actuator Adjustment Procedure Now Used on R1300G Load Haul Dump Machines {1265, 1716}
730C2 Articulated Truck Stopping the Engine
2013/04/25 Improved Coolant Gasket Used on Certain 3500 Engines {1353, 1380, 7555}
2013/03/08 The Enclosure Latch Assembly Has Been Improved on Certain 24M Motor Graders {7263}
2013/03/01 New TOPCON Grade Controller Software Is Now Available For Certain Asphalt Pavers {7219, 7220, 7620}
2013/03/22 A New Universal Joint is Now Used on Certain Large Off-Highway Trucks {3108, 3251}
R1300G Load Haul Dump 3306 Engine Supplement Governor Actuator - Remove and Install
24M Motor Grader Hydraulic and Steering System Introduction
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Temperature Sensor (DPF) - Remove and Install
2013/03/04 Improved Installation of the Multifunctional Lever Harness As on Certain Off-Highway Trucks and Wheel Tractor-Scrapers {1408, 5737}
24M Motor Grader Hydraulic and Steering System Location of Components
2570C and 2670C Wheel Feller Bunchers Capacities (Refill)
24M Motor Grader Hydraulic and Steering System Control Manifold (Implement, Steering)