1993/01/18 Caterpillar


Part Number References For 0R2818, 0R2819, And 0R3231 Remanufactured 3208 Truck Engines {0374}

Usage:


Reference: Service Magazine; February 25, 1991; Page 19; "New 0R3231 Remanufactured 3208 Truck Engine Available."

The 0R2818, 0R2819, and 0R3231 Remanufactured 3208 Truck Engines replace the former 0R0937, 0R0974, and 0R0799 Remanufactured 3208 Truck Engines. The former engines are canceled. The new remanufactured engines have 17.5:1 compression ratio pistons. These pistons help reduce the quantity of white smoke generated during cold start conditions. These engines can be used in all the same applications as the former engines.

No single parts manual can be used to identify all the components in these 17.5:1 compression ration engine arrangements. However, all the serviced parts can be identified by using a combination of the parts manuals listed in the chart.

The 0R2076 Remanufactured Short Block can be used for all three of these engines. The 0R2821 Remanufactured Fuel Nozzle and 0R2822 Nozzle Kit are available as service replacements for the 7W3710 Fuel Nozzle.

The 0R2818, 0R2819, and 0R3231 Remanufactured 3208 Truck Engines will have "SERV MAG" and the date "JAN1893" stamped on the engine information plate. This information will appear in the reference serial number and reference arrangement number locations. The date refers to the Service Magazine in which this article appears. This article can be used as a reference to help ensure the correct parts are used when servicing these engines.

The 0R2818 and 0R2819 Remanufactured 3208 Truck Engines built prior to mid January 1993 were not stamped with a Service Magazine date. This article also applies to these earlier engines.

Caterpillar Information System:

1993/01/18 New Videotape "Detection of Air and Combustion Gases in the Cooling System" Available {0374,1350}
1992/12/21 New Bellows Assemblies Used In Turbocharger Groups{1052,1059}
1992/12/21 Modifying Former 2W8888 Rocker Arm Shaft For Use With New 8T7581 Rocker Arm Shaft Bolt{1102}
1992/12/21 New Cylinder Head Bolt Tightening Procedure{1100}
1992/11/30 New Cast Iron Deaerators Replace Former Aluminum Deaerators{1350}
1992/11/30 Procedure To Clean High Performance Marine Engine Air Filter{0374,1054}
1992/11/30 Procedure To Replace Cylinder Head Gasket{1124}
1992/11/30 New Fuel Priming Pump Kit Available{1258}
1992/11/30 Left Handed Threads In Compressor Nut On Some Caterpillar Turbochargers{1077,1053,1052}
1992/11/30 New Oil Pump Used As Service Replacement{3310}
1992/11/30 New Unit Injector Sleeve Used In Cylinder Head Groups{1125}
1992/11/30 New Cylinder Head Gasket Used{1124}
1993/01/18 Cylinder Pack Puller Groups Improved {0705,1239}
1993/01/18 New And Remanufactured Fuel Injector Reference {1290}
1993/01/18 New Grommets With Higher Temperature Capacity Used In Clamp Assemblies {1307,1052}
1993/01/18 New Exhaust Manifold Group Will Help Reduce Vibration On Bellows {1059}
1993/01/18 New Cylinder Head Group Used To Help Reduce The Amount Of Oil On The Valve Stems {1102,1109,1104}
1993/01/25 New Connecting Rod Bearing Used In Piston And Rod Groups {1219}
1993/01/25 Special Instruction For Installing VR3 Voltage Regulator On SR4 Generators Now Available {4450}
1993/01/25 Drive End Bearing Service For 50/75 Amp Brushless Alternators {1405}
1993/01/25 Unit Injector Tip Seal Deterioration {1290}
1993/01/25 Check Engine Water Pump Impeller Face Clearance If The Engine Experiences Symptoms Of Overheating {1361}
1993/02/01 New 9U6101 Lower Pilot Reamer Group Available{0670,1125}
1993/02/08 Maintenance Tips For 6I0799 Exhaust Restrictor; Additional Spring Improves Performance Of 6I0799 Exhaust Restrictor{1119,1061,1088}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.