Crankshaft Gear - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 8H-0663     | 轴承拉拔器     | 1     |
5F-7345 | 螺钉     | 1     | |
126-7183 | 十字挡块     | 1     | |
126-7177 | 拉拔器支腿     | 2     |
开始:
- 拆卸前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 拆卸"。
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将曲轴齿轮 (4) 从曲轴 (2) 上拆下。
Show/hide table
图 1 | g02048917 |
Show/hide table
图 2 | g02049073 |
- 如有必要,将键 (1) 和摩擦片 (3) 从曲轴 (2) 上拆下。
注: 除非键损坏,否则不要从曲轴上卸下键。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
B     | -     | 热板     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 如有必要,将新的摩擦片 (3) 安装到曲轴 (2) 上。
Show/hide table
图 3 | g02052055 |
- 如有必要,将新的键 (1) 安装到曲轴 (2) 上。
- 用工具 (B) 将曲轴齿轮 (4) 加热到 150° ± 50°C (302° ± 90°F)。 对准曲轴齿轮 (4) 中的键槽与曲轴中的键 (1) 。 将曲轴齿轮 (4) 安装到曲轴 (2) 上。 确保曲轴齿轮 (4) 的肩 (5) 朝向发动机前部。
Show/hide table
灼热的零件或部件会烫伤人体。 别让灼热的零件或部件触及您的皮肤。 为了保护您的皮肤,必须穿上保护衣或使用保护装备。 |
End By:
- 安装前壳体。 有关正确的步骤,请参阅 拆解和组装, "壳体(前)- 安装"。
- 安装发动机机油泵。 有关的正确步骤,请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install