Connecting Rod Bearings - Remove - Connecting rods in position
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 9U-7336     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 227-4390     | E12 Torx 套筒     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
开始:
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
废弃所有旧的连杆紧固件。 |
注: 如果需要更换所有连杆轴承,可以同时在两个气缸上进行本程序。 本程序可在下列气缸配对上同时进行。 1 和 6, 2和 5 和 3 和 4。 确保在从一对气缸换到另一对气缸之前安装完两对连杆轴承。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 安装"。
- 使用工具 (A) 转动曲轴,使曲轴销在下止点位置。
如有必要,拆卸电热塞。 有关正确的步骤,请参阅拆解和组装, "电热塞 - 拆卸和安装"。
注: 拆卸电热塞有助于卸下连杆轴承。 并不是一定要拆下电热塞。
- 连杆和连杆盖在位置 (X) 应该有蚀刻的编号。 连杆和连杆盖上的编号必须相互匹配。 如有必要,在连杆 (5) 和连杆盖 (2) 上作一个临时标记来识别气缸编号。
注: 不要在断面分裂式连杆上冲出识别标记。 不要在断面分裂式连杆上压印识别标记。
Show/hide table
图 1 | g03472036 |
位置 (X) 中的蚀刻编号 |
Show/hide table
图 2 | g01341322 |
- 使用工具 (B) 拆下螺栓 (1) 。 弃置螺栓 (1) 。
- 将连杆盖 (2) 从连杆 (5) 上拆下。
- 将下轴瓦 (3) 从连杆盖 (2) 上拆下。 保持轴瓦与连杆盖一体。
- 小心地将连杆 (5) 推入缸孔中,直到连杆 (5) 离开曲轴。 将上轴瓦 (4) 从连杆上拆下。 保持轴瓦一体。
注: 不要推压连杆的断面分裂面,否则会导致损坏。 不要使连杆接触活塞冷却喷嘴。
- 重复步骤 1 到步骤 6,拆卸其余的轴瓦。
注: 放置断面分裂式连杆时必须要安装连杆盖。 在完成轴瓦的拆卸程序后,立即进行安装程序。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Selector and Pressure Control Valve (Boom) - Remove and Install
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install