Refrigerant Compressor - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 进行拆解步骤前清洁部件外部有助于防止污垢进入内部机构。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
接触制冷剂会使人受伤。 接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。 制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。 拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。 通过燃着的香烟吸入制冷剂会使人受伤或死亡。 通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。 维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。 采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 堵上所有管路有助于防止油液损失,并有助于防止污染物进入系统。
- 将蓄电池断路开关转到断开位置。
- 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。
- 将软管组件 (1) 和软管组件 (2) 从制冷剂压缩机 (4) 上断开。 有关正确步骤,请参阅原始设备制造商(OEM)信息。
注: 用新盖盖住软管组件。 用新螺塞塞住制冷剂压缩机中的所有端口。
Show/hide table
图 1 | g02321153 |
制冷剂压缩机的典型示例(端口可能不同) |
- 将线束组件 (3) 从制冷剂压缩机 (4) 上断开。
- 拆下交流发电机皮带。 有关正确步骤,请参阅拆解和装配, "交流发电机皮带 - 拆卸和安装"。
Show/hide table
图 2 | g02321154 |
- 将螺栓 (6) 和螺栓 (7) 从制冷剂压缩机 (4) 上拆下。
注: 拆下螺栓时,支承制冷剂压缩机的重量。
- 将制冷剂压缩机 (4) 从支架 (5) 上拆下。
- 必要时,遵循步骤 8.a 至步骤 8.c 将制冷剂压缩机支架 (5) 从缸体上拆下。
- 将螺栓 (8) 从支架 (5) 上拆下。
- 将支架 (5) 从缸体上拆下。
- 标注定位销 (9) 在支架 (5) 中的位置。
Show/hide table
图 3 | g02100040 |
Show/hide table
图 4 | g02100041 |
安装步骤
- 必要时,遵循步骤 1.a 至步骤 1.d 将制冷剂压缩机支架 (5) 安装到缸体上。
- 确保支架 (5) 清洁且无磨损和损坏。 如有必要,更换支架。
- 确保所有定位销 (9) 无磨损和损坏。 如有必要,更换定位销。
- 将支架 (5) 定位到缸体上。 安装螺栓 (8) 并用手拧紧。
- 拧紧螺栓 (8) 至扭矩为 44 N·m (32 lb ft)。
Show/hide table
图 5 | g02100040 |
Show/hide table
图 6 | g02100041 |
- 将制冷剂压缩机 (4) 定位到支架 (5) 上。
注: 支承制冷剂压缩机的重量。
Show/hide table
图 7 | g02321154 |
- 将螺栓 (6) 和螺栓 (7) 安装到制冷剂压缩机 (4) 上。
- 拧紧螺栓 (6) 和螺栓 (7) 至扭矩为 22 N·m (195 lb in)。
- 安装交流发电机皮带。 有关正确步骤,请参阅拆解和装配, "交流发电机皮带 - 拆卸和安装"。
- 将线束组件 (3) 连接到制冷剂压缩机 (4) 上。
Show/hide table
图 8 | g02321153 |
制冷剂压缩机的典型示例(端口可能不同) |
- 将盖从软管组件上拆下,然后将螺塞从制冷剂压缩机端口上拆下。 将软管组件 (1) 和软管组件 (2) 连接到制冷剂压缩机 (4) 上。 有关正确的步骤,请参阅 OEM 信息。
- 有关正确的加注步骤请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统"。
- 将蓄电池断路开关转到接通位置。
Caterpillar Information System:
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
C7.1 Industrial Engine Boost Pressure Sensor - Remove and Install