Pistons and Connecting Rods - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 9U-7336     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 1U-6684     | 活塞环压缩器     | 1     |
C     | 227-4390     | E12 Torx 套筒     | 1     |
D     | 8T-3052     | 度数轮     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
废弃所有旧的连杆紧固件。 |
- 如果已暂时安装连杆盖,拆卸连杆盖。 如有必要,彻底清洁所有部件。
- 用清洁的发动机机油涂抹缸孔, 活塞环, 活塞的外表面 和 轴瓦(连杆)。
注: 执行间隙检查时,安装干燥的连杆轴瓦。 有关正确步骤,请参阅拆解和组装, "轴承间隙 - 检查"。 最终组装期间,将清洁的发动机机油涂覆在连杆轴瓦上。
注: 确保已将活塞和连杆组件安装在正确的气缸中。
- 使用工具 (A) 转动曲轴,使曲轴销在下止点位置。 使用清洁的发动机机油润滑曲轴销。
- 将工具 (B) 安装在活塞 (4) 上。
注: 确保将工具 (B) 安装正确,活塞 (4) 能顺利地从工具滑出。
注: 活塞顶部的箭头必须朝向发动机前部。 连杆轴瓦的定位凸舌和活塞冷却喷嘴必须在发动机的同一侧。
Show/hide table
图 1 | g02013213 |
- 小心地将活塞和连杆组件推入缸孔中,推到曲轴销上。
注: 不要损坏曲轴销的精加工表面。
- 将连杆盖 (2) 安装到连杆 (1) 上。
注: 确保连杆盖 (2) 位置 (X) 与连杆 (1) 位置 (X) 上的蚀刻编号相互匹配。 确保连杆盖 (2) 的朝向正确。 上下轴瓦的定位凸舌应在同一侧。
Show/hide table
图 2 | g03472016 |
- 将新螺栓 (3) 安装到连杆 (1) 上。 使用工具 (C) 均匀拧紧螺栓至扭矩为 40 N·m (30 lb ft)。
注: 请勿重复使用旧螺栓来固定连杆盖。
- 顺时针再转动螺栓 120 度。 使用工具 (C) 和工具 (D) 以获得正确的最终扭矩。
- 确保连杆组件安装后有能感觉到的侧隙。 转动曲轴,确保没有卡滞。
- 重复步骤 2 至 9,安装其余的活塞和连杆。
End By:
- 安装活塞冷却喷嘴。 有关正确的步骤,请参阅 拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
- 安装缸盖。 有关正确的步骤,请参阅 拆解与组装, "气缸盖 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Selector and Pressure Control Valve (Boom) - Remove and Install
C7.1 Industrial Engine Camshaft - Remove and Install
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install