Pistons and Connecting Rods - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-1857     | 挡圈钳     | 1     |
B     | 1U-6683     | 活塞环扩张器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 如果已组装原来的活塞,按照步骤 2.a 至步骤 2.e 安装活塞环。.
- 将控油环 (3) 的弹簧放置到活塞 (4) 的控油环槽中。 中心线必须位于弹簧端部以内。
- 定位控油环,使 "TOP" 字样处于朝上位置。 使用工具 (B) 将控油环 (3) 安装到活塞和弹簧上。
注: 确保中心线距活塞环间隙 180 度。
- 使用工具 (B) ,将中间压缩环 (2) 安装到活塞 (4) 的第二道环槽中。 "TOP" 字样应朝上。 内表面上的倒角必须朝下。
- 使用工具 (B) 将顶部压缩环 (1) 安装到活塞 (4) 的顶环槽中。 "TOP" 字样应朝上。
注: 确保安装的顶部活塞环上的倒角 (W) 处于朝上位置。
- 定位活塞环,使其间隙彼此之间相隔 120 度左右。
注: 提供的新活塞组件配有新活塞环。
Show/hide table
图 1 | g03454416 |
- 如果更换了连杆组件 (6), 衬套 (8) 和 活塞销 (7) ,请参阅技术规格, "连杆"以了解更多信息。
Show/hide table
图 2 | g02210673 |
Show/hide table
图 3 | g02090053 |
Show/hide table
注意 |
---|
必须由受过正确培训的人员进行连杆中的活塞销衬套拆卸工作。 此外,还需使用专用机械。 有关更多资料,请咨询当地授权的卡特彼勒代理商。 |
- 使用清洁的发动机机油润滑连杆中活塞销 (7) 的衬套 (8) 。 使用清洁的发动机机油润滑活塞 (4) 中的活塞销孔。
- 将活塞 (4) 顶部朝下放置在适当的表面上。 将连杆 (6) 的锻造标记 (X) 定位到活塞上的方形凸台 (14) 。 确保连杆上的槽 (13) 正确定位。 请参阅图 3。
- 将活塞销 (7) 安装到活塞 (4) 上。
注: 如果活塞销用手不能安装,加热活塞至温度为 45° ± 5°C (113° ± 9°F)。
- 使用工具 (A) 将卡环 (5) 安装在活塞 (4) 的活塞销孔中。
注: 确保卡环座入活塞的环槽中。
- 将上轴瓦 (9) 安装到连杆 (6) 上。 确保轴承上轴瓦的定位凸舌正确座入连杆的槽 (13) 中。
- 将下轴瓦 (10) 安装到连杆盖 (11) 上。 确保下轴瓦的定位凸舌正确座入连杆盖的槽中。
- 放置断面分裂式连杆时必须要安装连杆盖。 从发动机上取出组件后,暂时将连杆盖 (11) 和螺栓 (12) 安装到连杆 (6) 上。 确保连杆盖与连杆上的蚀刻编号相互匹配。 确保连杆盖的朝向正确。 上下轴瓦的定位凸舌应在同一侧。 拧紧螺栓 (12) 至扭矩为 20 N·m (177 lb in)。
- 对于其余的活塞和连杆组件,重复步骤 2 至 10。
End By: 安装活塞和连杆。 有关正确的步骤,请参阅 拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Selector and Pressure Control Valve (Boom) - Remove and Install
C7.1 Industrial Engine Camshaft - Remove and Install
2012/11/26 A New Steering Cylinder Pin Assembly Is Now Available For Certain 16M Motor Graders {4303}
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install