Crankshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-8221     | 吊索     | 2     |
开始:
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
- 拆卸前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 拆卸"。
- 拆下曲轴后密封。 有关正确的步骤,请参阅拆解和组装, "曲轴后油封 - 拆卸"。
- 如有必要,拆卸缸盖。 有关的正确程序,请参阅拆解与组装, "缸盖 - 拆卸"。
- 如有必要,拆卸活塞和连杆。 有关正确的步骤,请参阅拆解和组装, "活塞和连杆 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 应将发动机倒置安装在适当的台架上。
- 如果还没有卸下缸盖、活塞和连杆,卸下连杆轴承。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 拆卸"。
- 确保标出主轴承盖的位置和朝向。
- 将螺栓 (3) 从管组件 (2) 上拆下。
Show/hide table
图 1 | g02204377 |
- 将管组件 (2) 从缸体上拆下。
- 拆下密封垫 (1) (未显示)。
- 从缸体上卸下螺栓 (4) 和主轴承盖 (5) 。
Show/hide table
图 2 | g02212653 |
Show/hide table
图 3 | g02212654 |
- 将主轴承下轴瓦 (6) 从主轴承盖 (5) 上拆下。 保持主轴承下轴瓦与相应的主轴承盖一体。
注: 主轴承下轴瓦是一个没有油孔的普通轴瓦。
- 对于 6 号主轴承,从缸体上卸下两个止推垫圈 (7) 。 为拆卸止推垫圈 (7) ,朝正确方向转动曲轴。 如有必要,转动曲轴时,朝发动机前端推动曲轴,以便有助于拆卸。 如有必要,转动曲轴时,朝发动机后端推动曲轴,以便有助于拆卸。
注: 止推垫圈的一端有一个定位凸舌。
Show/hide table
图 4 | g02212693 |
- 将工具 (A) 和适当的起吊设备连接到曲轴 (8) 上。 将曲轴 (8) 吊出缸体。 曲轴的重量约为 61 kg (134 lb)。
注: 不要损坏曲轴上的任何精加工表面。 从发动机上拆下曲轴之后,必须将曲轴支撑在适当的台架上,以避免损坏曲轴正时。
Show/hide table
图 5 | g02212655 |
- 从缸体上卸下主轴承上轴瓦 (9) 。 保持主轴承上轴瓦与相应的主轴承盖一体。
注: 上主轴瓦有一个凹槽和两个油孔。
Show/hide table
图 6 | g02212656 |
- 如有必要,拆卸曲轴正时齿圈。 有关正确的步骤,请参阅拆解和组装, "曲轴正时齿圈 - 拆卸和安装"。
- 如有必要,拆卸曲轴齿轮。 有关正确的步骤,请参阅拆解和组装, "曲轴齿轮 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install