Pistons and Connecting Rods - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-1857     | 挡圈钳     | 1     |
B     | 1U-6683     | 活塞环扩张器     | 1     |
开始:
- 拆下活塞和连杆。 有关正确的步骤,请参阅拆解和组装, "活塞和连杆 - 拆卸"。
注: 在活塞和连杆组件的部件上作一个临时标记。 这能确保将每个活塞和连杆组件的部件重新安装在原来的气缸中。 标记活塞在活塞销前凸台上的底面。 请勿交换使用部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将螺栓 (12) 和连杆盖 (11) 从连杆 (6) 上拆下。 废弃螺栓。
注: 放置断面分裂式连杆时必须要安装连杆盖。 在完成活塞和连杆的拆解程序后,应立即进行组装程序和安装程序。 有关正确的步骤,请参阅拆解和组装, "活塞和连杆 - 组装"和拆解和组装, "活塞和连杆 - 安装"。
Show/hide table
图 1 | g01341306 |
Show/hide table
图 2 | g02383077 |
- 将下轴瓦 (10) 从连杆盖 (11) 上拆下。 将上轴瓦 (9) 从连杆 (6) 上拆下。 保持轴瓦一体。
- 将活塞和连杆组件连杆朝上地放置在适当的表面上。 使用工具 (A) 拆下卡环 (5) 。
注: 注意锻造标记 (X) 的位置。 锻造标记旨在确保连杆组件和活塞组件的方位正确。
- 将活塞销 (7) 和连杆 (6) 从活塞 (4) 上拆下。
注: 如果活塞销用手不能拆卸,加热活塞至温度为 45 ± 5 °C (113 ± 9 °F)。 不要使用喷枪加热活塞。 记录连杆 (6) 和活塞 (4) 的朝向。
- 将活塞顶部朝上放在适当的表面上。 使用工具 (B) ,从活塞 (4) 上卸下压缩环 (1) 和 (2) 及控油环 (3) 。
注: 作好临时识别标记,以便识别压缩环 (1) 、压缩环 (2) 和控油环 (3) 的位置和方向。
- 检查连杆有无磨损或损坏。 如有必要,更换连杆 (6) 或更换活塞销 (7) 的衬套 (8) 。
注: 如果更换了连杆或活塞销的衬套,有关更多信息,请参阅技术规格, "连杆"。
Show/hide table
注意 |
---|
必须由受过正确培训的人员进行连杆中的活塞销衬套拆卸工作。 此外,还需使用专用机械。 有关更多资料,请咨询当地授权的卡特彼勒代理商。 |
- 重复步骤 1 至 6,拆解其余的活塞和连杆。
Caterpillar Information System:
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Selector and Pressure Control Valve (Boom) - Remove and Install
C7.1 Industrial Engine Camshaft - Remove and Install
2012/11/26 A New Steering Cylinder Pin Assembly Is Now Available For Certain 16M Motor Graders {4303}
C7.1 Industrial Engine Lifter Group - Remove and Install - Hydraulic Lifter Group
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install