Pistons and Connecting Rods - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 9U-7336     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 8S-2269     | 缸口铰刀     | 1     |
C     | 227-4390     | E12 Torx 套筒     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
开始:
- 拆下缸盖。 有关的正确程序,请参阅拆解与组装, "缸盖 - 拆卸"。
- 拆下活塞冷却喷嘴。 有关正确的步骤,请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) ,转动曲轴,使曲柄销处于下止点位置。
- 使用工具 (B) 除去缸孔顶部内表面上的积碳。
- 连杆和连杆盖在侧面位置 (X) 中应有蚀刻编号。 连杆和连杆盖上的编号必须相互匹配。 确保标记连杆 (1) 和连杆盖 (2) 的正确位置。 如有必要,在连杆和连杆盖上做出一个临时的标记来识别缸号。
注: 请勿压印连杆组件。 在连杆组件上压印或冲孔会导致连杆断裂。
Show/hide table
图 1 | g03471998 |
- 使用工具 (C) 拆下螺栓 (3) 。 将连杆盖 (2) 从连杆 (1) 上拆下。
- 小心地把活塞 (4) 和连杆推出缸孔。 将活塞 (4) 抬出缸体顶部。
注: 不要推压连杆的断面分裂面,否则会导致损坏。
Show/hide table
图 2 | g02013134 |
- 对其余的活塞和连杆,重复步骤 1 至步骤 5。
注: 放置断面分裂式连杆时必须要安装连杆盖。 从发动机上取出组件后,暂时将连杆盖 (2) 和螺栓 (3) 安装到连杆 (1) 上。 确保连杆盖与连杆上的蚀刻编号相互匹配。 确保连杆盖的方位正确。 上下轴瓦的定位凸舌应在同一侧。 拧紧螺栓 (3) 至扭矩为 20 N·m (177 lb in)。
Caterpillar Information System:
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
521B and 522B Track Feller Bunchers Machine Systems Selector and Pressure Control Valve (Boom) - Remove and Install
C7.1 Industrial Engine Camshaft - Remove and Install
2012/11/26 A New Steering Cylinder Pin Assembly Is Now Available For Certain 16M Motor Graders {4303}
C7.1 Industrial Engine Lifter Group - Remove and Install - Hydraulic Lifter Group
C7.1 Industrial Engine Cylinder Head - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}