Connecting Rod Bearings - Install - Connecting rods in position
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 9U-7336     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 227-4390     | E12 Torx 套筒     | 1     |
C     | 8T-3052     | 度数轮     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
废弃所有旧的连杆紧固件。 |
- 检查曲轴销有无损坏。 如果曲轴已损坏,更换曲轴。 有关正确的步骤,请参阅拆解和组装, "曲轴 - 拆卸"和拆解和组装, "曲轴 - 安装"。 确保轴瓦清洁且无磨损或损坏。 如有必要,更换轴瓦。
注: 如果更换了轴瓦,检查之前是否安装了加大尺寸的轴瓦。
- 将上轴瓦 (4) 安装到连杆 (5) 上。 确保上轴瓦的定位凸舌正确座入连杆的槽中。
注: 上轴瓦的两端必须位于连杆中央。 上轴瓦的两端与连杆配合面的距离必须相等。
Show/hide table
图 1 | g02015553 |
- 使用清洁的发动机机油润滑上轴瓦 (4) 。
- 使用工具 (A) 转动曲轴,使曲轴销在下止点位置。
- 小心地拉动连杆 (5) ,使其抵到曲轴销上。
注: 不要使连杆接触活塞冷却喷嘴。
- 清洁连杆盖 (2) 。 将下轴瓦 (3) 安装到连杆盖 (2) 上。 确保下轴瓦的定位凸舌正确座入连杆盖的槽中。
- 使用清洁的发动机机油润滑曲轴销和下轴瓦 (3) 。
- 将连杆盖 (2) 安装到连杆 (5) 上。
注: 确保连杆盖 (2) 位置 (X) 与连杆 (5) 位置 (X) 上的蚀刻编号相互匹配。 确保连杆盖的朝向正确。 上下轴瓦的定位凸舌应在同一侧。
Show/hide table
图 2 | g03472037 |
位置 (X) 中的蚀刻编号 |
- 使用工具 (B) 将新螺栓 (1) 安装到连杆上。 均匀拧紧螺栓至扭矩为 40 N·m (30 lb ft)。
注: 请勿重复使用旧螺栓来固定连杆盖。
- 顺时针方向将螺栓再转动 120 度。 使用工具 (B) 和工具 (C) 以获得正确的最终扭矩。
- 确保连杆组件安装后有能感觉到的侧隙。 转动曲轴,确保没有卡滞。
- 重复步骤 2 至步骤 11,以便安装其余的连杆轴承。
注: 如果需要更换所有连杆轴承,可以同时在两个气缸上进行本程序。 本程序可在下列气缸配对上同时进行。 1 和 6, 2和 5 和 3 和 4。 确保在从一对气缸换到另一对气缸之前安装完两对连杆轴承。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 安装"。
- 如果卸下了电热塞,安装电热塞。 有关正确的步骤,请参阅拆解和组装, "电热塞 - 拆卸和安装"。
End By: 安装发动机机油泵。 有关的正确步骤,请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Pistons and Connecting Rods - Assemble
C7.1 Industrial Engine Pistons and Connecting Rods - Disassemble
C7.1 Industrial Engine Pistons and Connecting Rods - Remove
C7.1 Industrial Engine Piston Cooling Jets - Remove and Install
C7.1 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Pilot Oil) - Remove and Install
C7.1 Industrial Engine Camshaft Bearings - Remove and Install
C7.1 Industrial Engine Camshaft Gear - Remove and Install
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Camshaft Position Sensor - Remove and Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum