Camshaft Position Sensor - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将锁片 (2) 滑入解锁位置。 将线束组件 (1) 从凸轮轴位置传感器 (3) 上断开。
Show/hide table
图 1 | g02022992 |
- 拆下螺栓 (4) 。 小心地将凸轮轴位置传感器 (3) 从缸体上拆下。
注: 不要使用杆或凸轮轴位置传感器上的线束连接将凸轮轴位置传感器从缸体上拆下。
- 将 O 形密封圈 (5) 从凸轮轴位置传感器 (3) 上拆下。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新的 O 形密封圈 (5) 安装到凸轮轴位置传感器 (3) 上。
注: 不要润滑 O 形密封圈。
Show/hide table
图 2 | g02022992 |
- 将凸轮轴位置传感器 (3) 安装到缸体上。 安装螺栓 (4) 并用手拧紧螺栓至扭矩为 14 N·m (124 lb in)。
- 将线束组件 (1) 连接到凸轮轴位置传感器 (3) 上。 将锁片 (2) 滑动到锁定位置。
Caterpillar Information System:
C7.1 Industrial Engine Atmospheric Pressure Sensor - Remove and Install
C7.1 Industrial Engine Refrigerant Compressor - Remove and Install
2012/08/21 A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1250, 1261}
C7.1 Industrial Engine Crankshaft Gear - Remove and Install
C7.1 Industrial Engine Crankshaft Timing Ring - Remove and Install
C7.1 Industrial Engine Crankshaft - Install
C7.1 Industrial Engine Crankshaft - Remove
C7.1 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
Comfort Series Seat For Caterpillar Machines Seat Maintenance Interval Schedule
C7.1 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Industrial Engine Pistons and Connecting Rods - Install
C7.1 Industrial Engine Crankshaft Position Sensor - Remove and Install
CB44B Vibratory Asphalt Compactor Propel System Piston Pump Neutral - Test and Adjust - Mechanical , Split Drum
521B and 522B Track Feller Bunchers Machine Systems Solenoid Valve and Manifold (Disc Saw) - Remove and Install
C7.1 Industrial Engine Coolant Temperature Sensor - Remove and Install
C7.1 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Fuel Temperature Sensor - Remove and Install
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
C7.1 Industrial Engine Boost Pressure Sensor - Remove and Install
C7.1 Industrial Engine Inlet Manifold Temperature Sensor - Remove and Install
C7.1 Industrial Engine Glow Plugs - Remove and Install