Relief Valve (Screed Counterbalance) - Test and Adjust
Show/hide table
柴油发动机的排气含有可伤害人体的燃烧产物。 必须要在通风良好的地方起动发动机,如果在密闭的地方起动,就要把排气通到外面。 |
Show/hide table
旋转和运动的部件会造成人身伤害。 应避开所有旋转和运动的部件。 机器移动或发动机运转时决不能试图进行部件的调整工作,除非另有规定。 机器必须停在水平地面上,且发动机停止运转。 维修、修理或调整机器前,在起动开关和控制装置上要贴上"禁止操作"或类似的警告标签。 |
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
- 把机器开到平整水平的路面。
- 将行驶操纵杆 (1) 移到 NEUTRAL(空档)位置。
Show/hide table
图 1 | g02597377 |
- 将转速旋钮 (4) 转到 MINIMUM(最小)位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
- 将行驶模式开关 (3) 移到 PAVE(摊铺)位置。
注: 要操作熨平板提升系统、料斗系统、斗门系统和螺旋布料器提升系统,机器必须处于 PAVE(摊铺)模式。
- 将熨平板提升开关 (5) 移到 FLOAT(浮动)位置。 将熨平板降至地面。
Show/hide table
图 2 | g02597379 |
- 按下降锁定键 (6) ,接合熨平板下降锁定功能。
Show/hide table
图 3 | g02597380 |
- 将油门控制开关 (7) 移到 LOW IDLE(低怠速)位置。 将开关保持在该位置少于 1 秒。
Show/hide table
图 4 | g02597381 |
- 按主页键 (8) 显示 advisor 显示器上的主页菜单。
Show/hide table
图 5 | g02597382 |
- 使用向上箭头 (9) 和向下箭头 (10) 导航主页菜单。 突出显示"控制"并按确定键 (11) 。
Show/hide table
图 6 | g02597383 |
- 突出显示"配置参数"并按确定键 (11) 。
Show/hide table
图 7 | g02597384 |
- 突出显示"控制平衡压力命令"并按确定键 (11) 。
Show/hide table
图 8 | g02597396 |
- 使用向上箭头 (9) 和向下箭头 (10) 调整熨平板辅助压力设定值。 将压力设定到 25 psi。 按确定键 (11) 保存值。
Show/hide table
图 9 | g02597398 |
- 按主页键 (8) 显示主页菜单。 突出显示"性能"并按确定键 (11) 。
Show/hide table
图 10 | g02597399 |
- 监控"性能参数"屏幕上的平衡压力。 压力应与步骤 13 中设定的熨平板辅助压力相等。
Show/hide table
图 11 | g02597400 |
- 按主页键 (8) 显示 advisor 显示器上的主页菜单。
- 使用向上箭头 (9) 和向下箭头 (10) 导航主页菜单。 突出显示"控制"并按确定键 (11) 。
- 突出显示"配置参数"并按确定键 (11) 。
- 突出显示"控制平衡压力命令"并按确定键 (11) 。
- 使用向上箭头 (9) 和向下箭头 (10) 调整熨平板辅助压力设定值。 将压力设定到 75 psi。 按确定键 (11) 保存值。
- 按主页键 (8) 显示主页菜单。 突出显示"性能"并按确定键 (11) 。
- 监控"性能参数"屏幕上的平衡压力。 压力应与步骤 20 中设定的熨平板辅助压力相等。
- 如果压力读数增加,转到步骤 25。 如果压力未增加,将发动机起动开关 (12) 移到 OFF(断开)位置。 对于配备辅助压力传感器和/或熨平板辅助电磁阀进行故障诊断与排除。
Show/hide table
图 12 | g02597402 |
- 系统压力在 0 - 6205 kPa (0 - 900 psi) 之间。 系统未指定摊铺设定值,可调整。 将熨平板辅助压力设定为 517 kPa (75 psi)。
- 将发动机起动开关 (12) 移到 OFF(断开)位置。 测试完成。
Caterpillar Information System:
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Rear Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Drive Shaft - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Speed Control (PWM) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Assemble
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Disassemble
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Auger Conveyor and Drag Conveyor) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Neutral (Auger Conveyor and Drag Conveyor) - Test and Adjust
2011/06/06 Improved Seal and Retainer Ring is Available for Certain Articulated Trucks {4008}
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Hitch Drive Shaft - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Front Drive Shaft - Remove and Install
2011/06/08 New Software Containing Engine Idle Shutdown Feature (EIS) Is Now Used on Certain Off-Highway Trucks {1920, 7620}
2470C, 2570C and 2670C Wheel Feller Bunchers Machine Systems Steering Cylinder - Remove and Install
2011/07/28 Correction to Disassembly and Assembly , "Final Drive and Brake - Install" for R2900G Load Haul Dump Machines {4050, 4251}
C27 and C32 Engines for Caterpillar Built Machines Cylinder Block
C175-16 Locomotive Engine Valve Mechanism
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Axle Shaft - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Front Axle - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Vibration Damper
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Axle - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Throttle Lock - Test
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Travel System
992K Wheel Loader Object Detection Sensor - Clean/Inspect