Rear Drive Shaft - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8S-7610     | 底座     | 1     |
8S-7650 | 油缸     | 1     | |
3S-6224 | 电动液压泵     | 1     | |
8S-7615 | 销     | 1     | |
B     | 155-3597     | 车轮楔子     | 4     |
Show/hide table
带载的传动系拧紧扭矩可造成人身伤害。 不等的车轮转速可产生传动系拧紧扭矩,从而使传动系部件在拆解中带载。 拆解前,务必释放传动系拧紧扭矩。 |
- 利用工具 (A) 升起后桥,直到一个车轮离地。 这将释放动力传动系内的传动系拧紧扭矩。 将车轮重新降至地面后拆下工具 (A) 。
Show/hide table
图 1 | g00836890 |
- 利用工具 (B) 稳定机器,以便于保养。
- 拆下螺栓 (1) ,以便将驱动轴 (2) 从后驱动桥的轭上断开。 利用撬棍将驱动轴 (2) 从后驱动桥的轭上分离。
Show/hide table
图 2 | g00564946 |
- 拆下螺栓 (3) ,以便将驱动轴 (2) 从中间驱动桥的轭上断开。 由两人和撬棍将驱动轴从机器上拆下。 驱动轴 (2) 的重量约为 44 kg (95 lb)。
Show/hide table
图 3 | g00854688 |
- 将唇形密封 (4) 从驱动轴 (2) 上拆下。 记下唇形密封的方位,以便于安装。
Show/hide table
图 4 | g00817664 |
安装步骤
- 按与拆卸相反的顺序安装驱动轴 (2) 。
- 拧紧螺栓 (3) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
- 拧紧螺栓 (2) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Caterpillar Information System:
AP1000E and BG1000E Asphalt Pavers Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Drive Shaft - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Speed Control (PWM) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Assemble
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Disassemble
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Auger Conveyor and Drag Conveyor) - Test
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Neutral (Auger Conveyor and Drag Conveyor) - Test and Adjust
2011/06/06 Improved Seal and Retainer Ring is Available for Certain Articulated Trucks {4008}
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Hitch Drive Shaft - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Front Drive Shaft - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Main Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Screed Counterbalance) - Test and Adjust
2011/06/08 New Software Containing Engine Idle Shutdown Feature (EIS) Is Now Used on Certain Off-Highway Trucks {1920, 7620}
2470C, 2570C and 2670C Wheel Feller Bunchers Machine Systems Steering Cylinder - Remove and Install
2011/07/28 Correction to Disassembly and Assembly , "Final Drive and Brake - Install" for R2900G Load Haul Dump Machines {4050, 4251}
C27 and C32 Engines for Caterpillar Built Machines Cylinder Block
C175-16 Locomotive Engine Valve Mechanism
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Axle Shaft - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Front Axle - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Vibration Damper
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Axle - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Throttle Lock - Test
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Travel System