735B, 740B and 740B EJECTOR Articulated Trucks Power Train Caterpillar


Front Drive Shaft - Remove and Install

Usage:

735B L4D

拆卸步骤

表 1
所需工具    
工具     零件号     零件说明     数量    
A     8S-7610     底座     1    
8S-7650 油缸     1    
3S-6224 电动液压泵总成     1    
8S-7615 销     1    

开始:

  1. 安装转向机架锁。

------ WARNING! ------

带载的传动系拧紧扭矩可造成人身伤害。

不等的车轮转速可产生传动系拧紧扭矩,从而使传动系部件在拆解中带载。

拆解前,务必释放传动系拧紧扭矩。


  1. 将蓄电池断路开关转到断开位置。



    图 1g00836890

  1. 利用工具 (A) 升起前桥,直到一个车轮离地。 这将释放前桥内的传动系拧紧扭矩。 拆下工具 (A) 。



    图 2g01187056

  1. 拆下螺栓 (1) ,以便将驱动轴 (2) 从前桥上断开。



    图 3g00816940

  1. 拆下螺栓 (3) ,以便将驱动轴 (2) 从输出分动器 (4) 上断开。

  1. 由两人将驱动轴 (2) 从机器上拆下。 驱动轴 (2) 的重量约为 30 kg (60 lb)。



    图 4g00847873

  1. 将唇形密封 (5) 从驱动轴 (2) 上拆下。 记下唇形密封的方位,以便于安装。

安装步骤

  1. 按与拆卸相反的顺序安装驱动轴 (2) 。

    1. 拧紧螺栓 (3) 至 135 ± 20 N·m (100 ± 15 lb ft) 的扭矩。

    1. 拧紧螺栓 (1) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。

Caterpillar Information System:

735B, 740B and 740B EJECTOR Articulated Trucks Power Train Main Drive Shaft - Remove and Install
Cat Water Delivery System (WDS) Hydraulic System Oil - Change
992K Wheel Loader Display and Camera - Clean - If Equipped
Cat Water Delivery System (WDS) Monitoring System
3516B Engine for 994F and 994H Wheel Loaders Sensor Supply - Test
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Crankcase Guard (Rear) - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Sensor Signal (Analog, Active) - Test
Installing Plates to Reduce Stress Concentration on the Axle on Certain 24H and 24M Motor Graders{4305, 4313, 5225} Installing Plates to Reduce Stress Concentration on the Axle on Certain 24H and 24M Motor Graders{4305, 4313, 5225}
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Steering Check and Combiner Valve - Remove and Install
3500 Marine Engines Alternator Mounting
992K Wheel Loader Window Washer Reservoir - Fill
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Radiator - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Hitch Drive Shaft - Remove and Install
2011/06/06 Improved Seal and Retainer Ring is Available for Certain Articulated Trucks {4008}
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump Neutral (Auger Conveyor and Drag Conveyor) - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor Case Drain Flow (Auger Conveyor and Drag Conveyor) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Disassemble
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Assemble
3516B Engine for 994F and 994H Wheel Loaders Speed Control (PWM) - Test
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Rear Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Screed Counterbalance) - Test and Adjust
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.