Axle Shaft - Remove and Install
拆卸步骤
左侧半轴
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-5832     | 撬杆     | 1     |
B     | 2P-8312     | 挡圈钳     | 1     |
C     | 1U-8848     | 轮轴安装器     | 1     |
Show/hide table
图 1 | g01183601 |
注: 由于半轴内部采用双列花键,因此左侧半轴必须采用以下程序。 如果采用正常拆卸程序,双列花键将卡住差速锁。
- 通过移动车轮将排放螺塞 (1) 定位到盖 (2) 的底部。 通过拆下排放螺塞进行放油。
Show/hide table
图 2 | g01183544 |
Show/hide table
图 3 | g01183545 |
- 拆下螺栓 (3) 和垫圈。 将盖 (2) 和 O 形密封圈 (4) 从终传动上拆下。
- 利用工具 (A) 定位半轴 (5) ,从而使太阳齿轮 (6) 与终传动齐平。 通过向后推太阳齿轮 (6) 接近挡圈 (7) 。 使用工具 (B) 拆下挡圈 (7) 。 拆下太阳齿轮 (6) 。
Show/hide table
图 4 | g01183559 |
Show/hide table
图 5 | g01183561 |
- 安装挡圈 (7) 。 挡圈 (7) 将用于防止工具 (C) 损坏。
Show/hide table
图 6 | g01183564 |
- 将适当的起吊设备和工具 (C) 固定到半轴 (5) 上。 半轴 (5) 的重量约为 35 kg (75 lb)。 通过将半轴 (5) 充分拉出终传动拆下工具 (C) 和重新定位适当的起吊设备。 拆下半轴 (5) 。
Show/hide table
图 7 | g01183582 |
Show/hide table
图 8 | g01183595 |
右侧半轴
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-5832     | 撬杆     | 1     |
B     | 2P-8312     | 挡圈钳     | 1     |
- 通过移动车轮将排放螺塞 (1) 定位到盖 (2) 的底部。 通过拆下排放螺塞进行放油。
Show/hide table
图 9 | g01183544 |
Show/hide table
图 10 | g01183545 |
- 拆下螺栓 (3) 和垫圈。 将盖 (2) 和 O 形密封圈 (4) 从终传动上拆下。
- 利用工具 (A) 拆下半轴 (5) ,从而使太阳齿轮与终传动齐平。
Show/hide table
图 11 | g01183559 |
Show/hide table
图 12 | g01183648 |
- 将适当的起吊设备固定到半轴 (5) 上。 半轴 (5) 的重量约为 35 kg (75 lb)。 拆下半轴 (5) 。
- 利用工具 (B) 将挡圈 (7) 从半轴 (5) 上拆下。 拆下太阳齿轮 (6) 。
Show/hide table
图 13 | g00846992 |
安装步骤
- 按与拆卸相反的顺序安装半轴 (5) 。
Caterpillar Information System:
C175-16 Locomotive Engine Valve Mechanism
C27 and C32 Engines for Caterpillar Built Machines Cylinder Block
2011/07/28 Correction to Disassembly and Assembly , "Final Drive and Brake - Install" for R2900G Load Haul Dump Machines {4050, 4251}
2470C, 2570C and 2670C Wheel Feller Bunchers Machine Systems Steering Cylinder - Remove and Install
2011/06/08 New Software Containing Engine Idle Shutdown Feature (EIS) Is Now Used on Certain Off-Highway Trucks {1920, 7620}
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Screed Counterbalance) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Rear Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Drive Shaft - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Speed Control (PWM) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Piston Pump (Steering) - Assemble
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Front Axle - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Vibration Damper
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Axle - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Throttle Lock - Test
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Travel System
992K Wheel Loader Object Detection Sensor - Clean/Inspect
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Control Valve (Travel)
2011/07/08 A New Pump Control Valve Group is Now Used on the Piston Pump Groups on Certain Off-Highway Trucks {5070}
2013/09/12 A New Aftercooler Core Assembly is Now Used in the Air Aftercooler Group on the 773F and 775F Off-Highway Trucks {1063, 1353, 1806}
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C27 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Leveling System