PRODUCT SUPPORT PROGRAM FOR REWORKING THE TRANSMISSION ON CERTAIN 745 ARTICULATED TRUCKS Caterpillar

PRODUCT SUPPORT PROGRAM FOR REWORKING THE TRANSMISSION ON CERTAIN 745 ARTICULATED TRUCKS

Usage:

TEBE9076-00

Show/hide table

15Apr2019

Q630
Q633

Show/hide table

Containment - Before/After (Limited distribution)	PRODUCT SUPPORT PROGRAM FOR REWORKING THE TRANSMISSION ON CERTAIN 745 ARTICULATED TRUCKS
1375 3016		PS90959

Show/hide table

NOTE:

Caterpillar’s obligations under this Service Letter are subject to, and shall not apply in contravention of, the laws, rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction, without recourse or liability with respect to Caterpillar.

NOTE:

This Containment Program can be administered either before or after a failure occurs. In either case the decision whether to apply the Program is made by the dealer and service rep. Obtain the service reps Goodwill Approver Code before completing the repair. EAME dealers should use their standard Industry Group specific goodwill approval codes. The Goodwill Approver Code must be included when submitting the claim.

Show/hide table

NOTE:	When reporting the repair, use "PS90959" as the Part Number and "7777" as the Group Number. If administered before failure, use "56" as Warranty Claim Description and "T" as the SIMS Description Code. If administered after failure, use "96" as Warranty Claim Description Code and use "Z" as the SIMS Description Code.
NOTE:	The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table

TERMINATION DATE

30Apr2020

PROBLEM

Show/hide table

The existing transmission can generate In Gear Slip Detect codes (IGSD) and may have clutch 4 and/or clutch 6 premature failures on certain 745 Articulated Trucks.

AFFECTED PRODUCT

Show/hide table

Model	Identification Number
745	3F600588, 590, 595-596, 602

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
4	0S1604	BOLT
2	1P3704	SEAL-RECTANGULAR
2	1P9216	RING-SEAL
1	1S6515	RING-SEAL
1	1T0234	RING-METAL SEAL
5	1T1597	RING-SEAL
2	1T1599	RING-SEAL
6	2J0157	SEAL-O-RING
1	2S1362	RING-SEAL
1	3D2824	SEAL-O-RING-STOR
2	3H4970	SEAL-O-RING
1	3K0360	SEAL-O-RING
1	3S1279	RING-SEAL
1	4F7389	SEAL-O-RING
4	4J0522	SEAL-O-RING
1	4M0189	SEAL-O RING
1	4M6480	GASKET
1	5P8286	SEAL-O-RING
2	6F0155	RING-METAL SEAL
2	6J2244	SEAL-O-RING
2	6T0248	RING-SEAL
1	6T0838	RING-SEAL
4	6U0455	STRAP
4	6U0456	LASHING TIE 20
1	6V1720	PLATE-SERIAL NO
1	6V3955	SEAL-O-RING
2	6V5141	SEAL-O-RING
1	6V8001	SEAL-O-RING
1	6V8398	SEAL-O-RING-ORFS
2	6Y2983	RING-SEAL
3	7M8485	SEAL-O-RING-STOR
1	7S7018	RING-SEAL METAL
1	7T5987	RING-SEAL
1	7X4744	SEAL-O-RING
1	8L2786	SEAL-O-RING
1	8P8744	RING-SEAL EXT
1	8T2611	RING-RETAINING
1	9G8718	RING-SEAL
1	9H0846	SEAL-O-RING
1	9M2008	RING-METAL SEAL
1	9U9484	RING-SEAL
1	0041964	SEAL-O RING
1	0619457	SEAL-O-RING
1	1073119	SEAL-O-RING
1	1336578	SEAL-O-RING
1	1503296	RING - SEAL
1	1650507	RING-SEAL (EXT)
2	1757904	SEAL-O-RING
4	2284947	SEAL-O-RING
2	2287092	SEAL-O-RING-ORFS
2	2287093	SEAL-O-RING-ORFS
1	2385082	SEAL-O-RING-STOR
3	2385084	SEAL-O-RING-STOR
1	2432737	SEAL-O-RING
1	2696932	BEARING-THRUST
1	3116130	SEAL-O-RING
1	3308197	SEAL-O-RING
1	3375270	ELEMENT AS-XMSN
6	3533952	DISC-FRICTION
6	3534888	PLATE-CLUTCH
56	3534922	BUTTON-THRUST
1	3534938	GASKET
1	3592811	GASKET
1	3592813	GASKET
1	3653179	SEAL-LIP TYPE
1	3679384	SEAL-O-RING
1	3679385	SEAL-O-RING
1	3704648	GASKET
1	3810187	GASKET
1	3853954	GASKET
1	3853955	GASKET
1	3872970	GASKET
1	3872971	GASKET
1	3872973	GASKET
1	4218199	VALVE GP-SOL
1	4255636	GASKET
1	4591195	BEARING-THRUST
1	4666259	RING-RETAINING
1	4677358	PISTON-CLUTCH
2	4780048	RING-SEAL
1	4886382	RING-SEAL
1	4908824	PLATE AS
2	5095767	RING-SEAL
1	5183168	RING-SEAL
7	5185072	VALVE GP-SOL
1	5200122	HUB-CLUTCH
1	5247954	HOUSING-CLUTCH
1	5247955	PISTON-CLUTCH
48	5387564	SCREW-TRUSS HEAD ***
2	5508164	PIN
1	5537191	SHAFT **
1	5705044	PLATE
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 32% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

Note: Some parts in the 'parts needed' list have been marked with (** or ***) identifiers. Please follow the associated notes, as they may not be needed for most repairs. Only order parts as needed.

** For the 553-7191, order only if you don?t have 471-9315 with EC01 ? see SMAG M0094535. Part number 471-9315 with Engineering Change number of 01 or has a supplier serial number equal to or greater than M446100 has all engineering updates and can still be used.

*** If 538-7564 Screws are not available and are holding up a transmission rebuild, work with your dealer TC to contact product support for alternate assembly instructions.

Note: Verify transmission being repaired is covered under PS53729 Service letter and perform update for intermediate sensors as needed. If the transmission being updated already had PS53729 Service Letter applied, DO NOT update intermediate sensors again.

Refer to SEHS0586, CX38 Transmission Dealer Rebuild Readiness Playbook ? for 735C, 740C, and 745C Articulated Truck.

Refer to SEBF8115, Transmission Clutch Plates and Disc Assemblies with Cellulose Friction Material Reuse And Salvage Guidelines.

Refer to M0072352, CX38 Transmission Pump Inspection Reuse And Salvage Guidelines.

Updating swings is permitted by this letter. Note warranty can?t be charged until the transmission is used in truck, thus up front labor and parts costs are the responsibility of the dealer until the time of install. (Not Parts Stock Action)

If the parts received are damaged, or if you have any questions you will need to work with your Dealer TC to submit the information or question through CPI Feedback within the Service Information Management System (SIMSi).
Give the information to your Dealer Technical Communicator (TC) along with this service letter program number and CPI number 365466.
Request the Dealer TC to submit the CPI Feedback.

Clear all logged and event codes from the transmission ECM. The Transmission Serial Number must be updated on the Trans/Chassis ECM otherwise, the new software will not work correctly. Later add the new serial numbers to SIMSi. Look for more instructions in "ON MACHINE TEST PROCEDURES" section below.

All machines being repaired under this service letter must be documented and summary of completed machines should be sent back to local Caterpillar Representative through email.

Repair Plan Methods:
Transmission rebuild and bench test facilities are required to perform the Disassembly and Assembly repair of the transmission.

Refer to the attached Rework Procedure.

Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-10000 hrs, 0-60 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 40.0-hour job If there has been a previous repair, part age/hours will apply. Retain a copy of the previous repair invoice in the dealer's records for audit purposes, and specify repair date and machine hours in the "Additional Comments" section of the warranty claim.
If the transmission being reworked was previously rebuilt, part age/hours will apply instead of machine hours towards the 10000 hour coverage. Only order parts as needed For the 553-7191 order only if you don?t have 471-9315 with EC01 ? see SMAG M0094535. Part number 471-9315 with Engineering Change number of 01 or has a supplier serial number equal to or greater than M446100 has all engineering updates and can still be used. * For updating Intermediate sensors. These parts are not required if the transmission being updated already had PS53729 Service Letter applied.

Show/hide table

PARTS DISPOSITION

Show/hide table

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Rework Procedure

Show/hide table

DISASSEMBLY AND ASSEMBLY PROCEDURES

Additional information is available for disassembly and assembly of the transmission.

A consolidated guide to rebuild readiness is available in the Shop Review section of SISweb. Refer to CX38 Transmission Dealer Rebuild Readiness Playbook for 735C, 740C, and 745C Articulated Truck Media Number - SEHS0586. The Playbook contains references to tooling lists, training materials, and inspection materials.

For access to a video for this procedure, scan the QR code below with a QR enabled device or copy the link below. If the link doesn't work, copy the entire link and paste in your web browser, make sure there are no gaps or spaces after you paste.

Caterpillar Channel 1 Video: "CX38 Disassembly and Assembly"
Media Number: CATU0825
Channel 1 URL (direct link to video):
https://channel1.mediaspace.kaltura.com/media/
CX38+Transmission+Disassembly+and+Assembly/1_hwtr6l0a

Image1.1.1

To Remove and Install the Torque Converter refer to: Disassembly and Assembly 735C, 740C EJECTOR and 745C Articulated Trucks Power Train Media Number - UENR4227.

For Disassembly and Assembly the Transmission Planetary refer to 735C, 740C EJECTOR and 745C Articulated Trucks Power Train Media Number - UENR4227.

TRANSMISSION BENCH TEST PROCEDURE

When the transmission has been assembled, test the transmission using the test bench procedure. Refer to: Bench Test Procedure for 735C, 740C, and 745C Articulated Truck Transmission. Media Number -REHS9381 - Bench Test Procedure for 735C, 740C, and 745C Articulated Truck Transmission.

TRANSMISSION INSTALLATION

Before installation of the transmission make sure that the transmission system is clean. Refer to Contamination Control Guidelines - SEBF9204 and Cleaning Fluid-Carrying Hose and Tube Assemblies In Shop and Field Applications - SEBF8485.

After transmission installation is complete Fill the transmission with oil. The correct oil level is critical to transmission functionality and on machine test procedures.

Refer to 735C and 745C Articulated Trucks Operations and Maintenance Media Number - SEBU9060 and 740C Ejector media number SEBU9061 - "Torque Converter, Transmission, and Transfer Gear Oil - Change".

SERIAL NUMBER PLATE PROCEDURE (Except Reman).

The serial number plate and the stamped serial number on the transmission case must be replaced or reworked to denote that updates have been completed. Remove the original serial number plate from the casing. Replace the serial plate with a new serial number plate.

Image1.5.1

Rework the "TRANS SERIAL NO" on the transmission serial number plate from an "M4Y, K38, TJ9, TW5 or TW6" number to a "DW3" number. For a REMAN, MJ8 prefix use the serial number stamped on the outside of the case to create the new serial number.

Note: The last five digits at the end of the "TRANS SERIAL NO" must remain the same.

Rework the "TRANS ARRANG NO" on the transmission serial number plate from the "353-4920", "518-9384", or "20R-6548" or "20R-8342" transmission part number to a "490-8822" part number.

Rework the "CONVERTER SERIAL NO" on the transmission serial number plate to reflect the same number stamped on the original serial number plate.

Clean and prepare the area where the serial number plate will be attached to the transmission case and then apply Loctite 7387 activator.

Apply Loctite 330 adhesive to the back of serial number plate before sticking it to the transmission case.

Note: You may have to hold in position for a short time.

Rework the Transmission Serial Number that is stamped into the transmission case (if applicable) from an "TJ9"(or other serial number prefix) number to a "DW3" number.

Note: The last five digits at the end of the stamped Transmission Serial Number must remain the same. Only change the "TJ9" number.

SERIAL PLATE PROCEDURE (REMAN):

The serial number plate on transmissions with a "Remanufactured Component" serial plate must be replaced.

Locate the original serial number stamped into the transmission case.

Stamp the "TRANS SERIAL NO." with "DW3" followed by the original five digit serial number from the transmission case.

Stamp the "TRANS ARRANG NO" with part number "490-8822".

Stamp the "CONVERTER SERIAL NO." with serial prefix "M7N". A five digit converter serial number is not required.

Clean and prepare the area where the serial number plate will be attached to the transmission case and then apply Loctite 7387 activator.

Apply Loctite 330 adhesive to the back of serial number plate before sticking it to the transmission case.

Note: You may have to hold in position for a short time.

Rework the Transmission Serial Number that is stamped into the transmission case (if applicable) from an "TJ9" number to a "DW3" number.

Note: The last five digits at the end of the stamped Transmission Serial Number must remain the same. Only change the "TJ9" number.

MAIN TRANSMISSION RELIEF VALVE

Reset the bias compensation for the Main Transmission Relief Valve: Refer to UENR4226 - Testing and Adjusting - Relief Valve (Transmission Main) Pressure - Test - Electronic Main Relief Valve - "Bias Reset".

TRANSMISSION CLUTCH CALIBRATION TESTS

The transmission requires 2 separate calibrations: 1) Engagement Calibration and 2) Transmission Fill Calibration, which are both completed through Cat ET.

Test 1

Perform the Engagement Calibration. Refer to UENR4226 - Testing and Adjusting for Transmission Engage Calibration.

NOTE: Remove pressure gauges and hoses from transmission pressure ports prior to performing Transmission Fill Calibration procedure.

Test 2

Perform the Transmission Fill Calibration. Refer to UENR4226 - Testing and Adjusting Transmission Fill Calibration procedure.

Road test truck by shifting truck up and down thru all forward gears. Also, perform neutral to forward gear and neutral to reverse gear shifts. Ensure all shifts have acceptable shift feel.

After repair is completed update transmission serial number updates in SIMSi.

ADDITIONAL INFORMATION ON MAJOR UPDATES IN PS53803

Clutch 4 Improvements:
Clutch 4 hub (520-0122) has improved lubrication to the clutch. The piston (524-7955) and housing (524-7954) have improve clutch stoke as to not allow the piston to come out of the bore when clutch 4 wears to any great degree which resulted with seal extrusion then loss of pressure.

Image1.7.1

Image1.7.2

Clutch 6 Improvements:
Clutch 6 plate assembly (490-8824) now contains an inside diameter seal groove. This requires a new piston seal ? 488-6382. The low gain piston (inner positioned) is now part number 467-7358. The design change allows the piston to come up evenly in the bore of the plate assembly, thus eliminating piston cocking. This led to heavy hot spotting and rough shifts when clutch 6 was activated; mainly forward 3rd to 4th and 8th to 9th. (Note this improvement is already in the 490-8822 production transmissions of the 740 EJ & 745 ATs). For C-Series transmission updates, making this update requires new software to be flashed on the Trans/Chassis which will control the clutch differently during shifts and differences in calibration. Software will be explained further later in this documentation.

Image1.8.1

Image1.8.2

Clutch 1/3 Pin Improvements:
The reaction pins in the clutch 1-3 balance piston groups are being updated. The new part number is 550-8164. Two are required per transmission build. This change is also explained with service magazine M0094265. (See pin ? label 1 in the pictures below)

Torque Converter Improvements:
The updated torque converter "L" washer design is intended to provide a better load path through the torque converter retention snap ring. The current design flat washer (370-3812) loads the snap ring with a bending moment that is believed to cause the snap ring to roll out of the mating main shaft groove. The updated "L" washer is design to load the snap ring in a more ideal shear direction that is more resistant to rolling out of the groove. Along with eliminating the bending moment on the snap ring, the "L" washer reduces the stress on the snap ring improving life 6x.

Image1.9.1

Image1.9.2

The intermediate speed sensors parts are being improved. Listed in the service letter (PS53803) for convenience, but are covered under service letter PS53729 when worked while the transmission is installed in the truck. The main parts are the following: 546-5409 Sensor Group and 549-7410 Harness. Two of each required for the rebuild. Other parts to go with the sensor changes are seal 3P-0647, 8T-6912 bolt and 354-5137 spacer. Two of each required for the rebuild. This change is also explained with service magazine M0089327.

(1) 546-5409 Speed Sensor Gp
(2) 8T-6912 Bolt
(3) 354-5137 Spacer
(4) 549-7410 Sensor Harness As