Coupling - Install
安装步骤
Show/hide table
所需工具     | |
工具     | 数量     |
限位夹具。 请参阅插图 1。     | 1     |
Show/hide table
图 1 | g00615434 |
限位夹具装配 (A) 114.3 mm (4.50 inch) (B) 19.7 mm (0.78 in) (C) 45.5 mm (1.79 in)(仅限 SR4B) (C) 39.4 mm (1.55 in)(仅限 SR4) (D) 50.8 mm (2.00 in) (E) 12.7 mm (0.50'') (F) 19.1 mm (0.75 inch) (G) 50.8 mm (2.00 in) |
- 将联轴器均匀加热至 400 °C (752.0 °F)。 烘箱是加热联轴器的首选方法。
注: 该驱动联轴器为重型过盈配合安装件。 请勿使用其他任何方法安装驱动联轴器。
- 将联轴器放在工作台上。
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
- 将限位夹具连到联轴器上。
Show/hide table
图 2 | g00615500 |
带有限位夹具的联轴器。 |
- 将联轴器在转子轴上滑动。 继续滑动联轴器,直至限位夹具接触转子轴。
Show/hide table
图 3 | g00615513 |
- 将限位夹具从联轴器上拆下。
Show/hide table
图 4 | g00615518 |
Caterpillar Information System:
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
3612 and 3616 Engines Piston Cooling Jets - Remove and Install
3114, 3116 and 3126 Engines Unit Injector Misfire
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3114, 3116 and 3126 Engines Soot in Inlet Manifold
G3612 and G3616 Engines Camshaft - Remove
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3612 and G3616 Engines Camshaft - Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head