Inlet and Exhaust Valve Seat Inserts - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A (1)     | 6V-4194     | 气门座拔取器     | 1     |
B (1)     | 165-5647     | 气门座拔取器     | 1     |
C (1)     | 6V-4804     | 手柄     | 1     |
D (1)     | 6V-4192     | 轴     | 1     |
E (1)     | 6V-4199     | 提升支架     | 1     |
Show/hide table
( 1 ) | 166-7441 气门座拔取器工具总成 的零件 |
开始:
- 拆下进气门和排气门。 请参阅拆解和组装, "进气与排气阀 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安装到排气门座圈内。
Show/hide table
图 1 | g00987231 |
Show/hide table
图 2 | g00987198 |
注: 将进气门座圈拆卸用工具 (A) 更换为工具 (B) 。
- 将工具 (C) 和工具 (D) 安装到工具 (A) 内。 用手上紧工具 (D) 。 工具 (A) 将膨胀到气门座圈 (1) 边缘的下方。
- 将工具 (E) 安装到缸盖上工具 (C) 的下方。 握住工具 (D) 的同时转动工具 (C) 。 拆下气门座 (1) 。
Show/hide table
图 3 | g00987225 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
F     | 149-6115     | 安装工具     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (F) 倒置后利用工具 (F) 和压具将气门座圈 (1) 安装到缸盖组件内。
Show/hide table
图 4 | g00987231 |
注: 不要为了纠正气门杆突出而加工已经加工好的气门座镶圈。 气门杆突出过量说明气门座镶圈没有安装到位或镗孔底部残渣未清理干净。
End By: 安装进气门和排气门。 请参阅 拆解和组装, "进气与排气阀 - 拆卸和安装"。
Caterpillar Information System:
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
G3612 and G3616 Engines Camshaft - Remove
SR4B Generators Coupling - Install
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
3612 and 3616 Engines Piston Cooling Jets - Remove and Install
G3612 and G3616 Engines Camshaft - Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3612 and G3616 Engines Crankshaft Main Bearings - Install
SR4B Generators Bearing - Remove and Install