Injection Actuation Pressure Control Valve - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-0333     | 爪型扳手     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将线束组件 (2) 从喷油驱动压力控制阀 (1) 上断开。
Show/hide table
图 1 | g01025581 |
Show/hide table
图 2 | g01025630 |
- 将螺母 (3) 、隔套 (5) 和电磁阀 (4) 从喷油驱动压力控制阀 (1) 上拆下。
- 利用工具 (A) 和加长杆将喷油驱动压力控制阀从单体喷油器液压泵上拆下。
- 将 O 形密封圈 (6) 和 (8) 以及支承环 (7) 从喷油驱动压力控制阀 (1) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-0333     | 爪型扳手     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新 O 形密封圈 (6) 和 (8) 以及支承环 (7) 安装到喷油驱动压力控制阀上。 利用干净的机油润滑 O 形密封圈。
Show/hide table
图 3 | g01025630 |
Show/hide table
图 4 | g01025581 |
- 利用工具 (A) 将喷油驱动压力控制阀安装到单体喷油器液压泵上。 将喷油驱动压力控制阀上紧到 50 ± 5 N·m (37 ± 4 lb ft) 的扭矩。
- 将电磁阀 (4) 、隔套 (5) 和螺母 (3) 安装到喷油驱动压力控制阀 (1) 上。 拧紧螺母 (3) 至扭矩为 5.5 ± 1.5 N·m (49 ± 13 lb in)。
- 将线束组件 (2) 连接到喷油驱动压力控制阀 (1) 上。
Caterpillar Information System:
G3304 and G3306 Engines Cylinder Head
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
C-9 Industrial Engine Engine Design
G3612 and G3616 Engines Camshaft - Install
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
G3612 and G3616 Engines Camshaft - Remove
SR4B Generators Coupling - Install
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3612 and G3616 Engines Crankshaft Main Bearings - Install
SR4B Generators Bearing - Remove and Install
G3612 and G3616 Engines Crankshaft - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
SR4B Generators Rotor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Assemble
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Remove