Piston Cooling Jets - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 9S-9082 | 发动机盘车工具 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A)转动曲轴,以便可以接近活塞冷却喷嘴。
- 拆下螺栓 (1) ,然后拆下活塞冷却喷嘴 (2)。
Show/hide table
图 1 | g01144041 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 9S-9082 | 发动机盘车工具 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A)转动曲轴,以便可以接近活塞冷却喷嘴。
注: 如果没有正确安装活塞冷却喷嘴的话,则可能会导致发动机损坏。 用手安装活塞冷却喷嘴。
- 将活塞冷却喷嘴 (2) 放置在缸体中。 确保活塞冷却喷嘴 (2) 与缸体平齐。 安装螺栓 (1)。 拧紧螺栓 (1),使其扭矩达到
28 ± 7 N·m (21 ± 5 lb ft) 。
Show/hide table
图 2 | g01144041 |
结束:
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
G3304 and G3306 Engines Cylinder Head
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
C-9 Industrial Engine Engine Design
G3612 and G3616 Engines Camshaft - Install
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
G3612 and G3616 Engines Camshaft - Remove
SR4B Generators Coupling - Install
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3612 and G3616 Engines Crankshaft Main Bearings - Install
SR4B Generators Bearing - Remove and Install
G3612 and G3616 Engines Crankshaft - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
SR4B Generators Rotor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Assemble
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test