Cylinder Liner - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
B | 235-0632 | 气缸安装工具总成 | 1 |
C | 191-1135 | 油缸压力机 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 检查缸套。 请参阅可重复使用的部件指南, SEBF8068, "缸套"。
Show/hide table
图 1 g00575575 - 在四个位置测量垫片的槽深。 槽的深度必须为
3.50 ± 0.05 mm (0.138 ± 0.002 inch) 。 槽的深度变化不得超过0.02 mm (0.001 inch) 。Show/hide table图 2 g00575577 - 在四个位置测量缸套法兰的厚度。 法兰的厚度必须为
33.00 ± 0.03 mm (1.299 ± 0.001 inch) 。 法兰的厚度变化不得超过0.013 mm (0.0005 inch) 。Show/hide table图 3 g00575579 - 使用缸径千分表在四个位置测量缸套的内径。 应在每个位置相隔 90 度的两个点测量缸套。 新缸套的内径为
300.025 ± 0.025 mm (11.8120 ± 0.0010 inch) 。Show/hide table图 4 g01441756 - 清除缸套外表面的锈蚀和/或沉积物。 使用玻璃珠或钢丝刷。
- 彻底清洁缸体中的缸套孔。 将肥皂水或 P80 橡胶润滑剂涂抹到密封表面。
- 将 O 形密封圈 (2) 和 O 形密封圈 (3) 安装在缸套 (1) 上。
- 将肥皂水或 P80 橡胶润滑剂涂抹到 O 形圈上。
- 将工具 (B) 和适当的起吊设备固定在缸套 (1) 上。
- 将缸套小心地降到缸体中。 降低缸套,直至缸套的下部 O 形密封圈进入缸体密封孔。
- 拆下工具 (B)。 用一个较大的橡胶锤轻击缸套顶部,以使缸套座入缸体中。 也可使用工具 (C) 使使缸套座入缸体中。
结束:
- 安装活塞和连杆。
Caterpillar Information System:
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
3612 and 3616 Engines Piston Cooling Jets - Remove and Install
3114, 3116 and 3126 Engines Unit Injector Misfire
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3114, 3116 and 3126 Engines Soot in Inlet Manifold
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
SR4B Generators Coupling - Install
G3612 and G3616 Engines Camshaft - Remove
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3612 and G3616 Engines Camshaft - Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove