Cylinder Liner - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-8568 | 缸套拆卸器总成 | 1 |
9U-6600 | 手动液压泵 | 1 | |
8T-3035 | 液压管 | 1 | |
8T-0820 | 液压压力表 | 1 | |
350-7768 | 电动液压泵总成
(115 V 50/50 Hz) |
1 | |
350-7769 | 电动液压泵总成
(230 V 50/60 Hz) |
1 |
开始:
- 卸下活塞和连杆。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 将冷却液从缸体中全部排出。
- 卸下缸盖和活塞。
- 将保护盖置于曲轴上方,以防止灰尘和碎屑落在曲轴上。
Show/hide table
图 1 g00575535 - 在缸套内安装工具 (A)。 将支腿放好,以与缸套底部接合。
- 将泵总成上的两个液压软管固定至工具 ( A) 上的液压油缸上。
- 使用工具 (A) 从缸体中拉出缸套。 直至下部 O 形密封圈从缸体孔上脱离。
Show/hide table
图 2 g00575536 - 将尼龙带和适当的起吊设备固定至工具 (A)。 将缸套 (1)从缸体中拉出。 缸套 (1) 和工具 (A) 的组合重量约为
127 kg (280 lb) 。Show/hide table图 3 g00575537 - 将 O 形密封圈 (2) 和 O 形密封圈 (3) 从缸套上拆下。
- 将缸套降低至缸体上。 拆下工具 (A)。
- 检查缸套。 请参阅可重复使用部件, 指南SEBF8068, "缸套"。
Caterpillar Information System:
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
3612 and 3616 Engines Piston Cooling Jets - Remove and Install
3114, 3116 and 3126 Engines Unit Injector Misfire
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3114, 3116 and 3126 Engines Soot in Inlet Manifold
3126B Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
C9 Engine For Caterpillar Built Machines Fuel Priming Pump - Remove and Install
G3612 and G3616 Engines Cylinder Liner - Install
SR4B Generators Coupling - Install
G3612 and G3616 Engines Camshaft - Remove
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3612 and G3616 Engines Camshaft - Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install