Camshaft - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 8T-3029 | 凸轮轴支架 | 1 |
1U-6311 | 板 | 1 |
开始:
- 拆下气门挺杆。 请参阅拆解和组装, "气门挺杆 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 从缸体侧面拆下凸轮轴检查盖。
注: 必须旋转发动机,以便拆下将凸轮轴齿块 (4) 固定到位的所有螺栓。
- 松开凸轮轴凸轮段 (4) 外侧的螺栓 (1)。
- 如果需要拆下凸轮轴轴颈 (2),则松开外径上的螺栓 (3)。
- 旋转发动机,直到之前朝向缸体内侧的螺栓 (1) 和螺栓 (3) 现在朝向缸体外侧。
- 松开其余的螺栓 (1) 和螺栓 (3)。
Show/hide table
图 3 g00615465 注: 不能在拆下凸轮轴驱动齿轮 (5) 后旋转发动机。 确保在拆下凸轮轴驱动齿轮前松开了所有必要的螺栓。
- 如果要卸下轴组件 (6),则先卸下凸轮轴主动齿轮 (5)。 更多信息,请参阅拆解和装配, "凸轮轴主动齿轮 - 拆卸"。
Show/hide table
图 4 g00575676 - 将工具 (A) 安装在凸轮轴齿块 (4) 下面。
- 拆下将凸轮轴齿块固定到位的螺栓 (1)。
- 小心地将凸轮轴前部分移向发动机前部。 这样做是为了断开凸轮轴齿块各端中的定位销。
- 小心地将凸轮轴齿块 (4) 从工具 (A) 上的发动机移出。
- 将适当的起吊设备连接到涡轮增压器 (4) 上。 凸轮轴凸轮段 (4) 的重量约为
28 kg (62 lb) 。 从工具 (A) 上卸下凸轮轴凸轮段 (4)。 在凸轮轴齿块上作识别标记,以便于安装。 - 从每个凸轮轴轴颈上拆下隔套。 将工具 (A) 从发动机上拆下。
- 拆下将凸轮轴轴颈 (2) 固定在其他凸轮轴齿块上的螺栓 (3)。
- 将凸轮轴轴颈 (2) 滑出凸轮轴轴承。 从发动机上拆下凸轮轴轴颈。 从轴颈上拆下隔套。
Show/hide table
图 5 g00615468 - 从轴组件 (6) 上卸下螺栓和盘 (8)。
- 卸下螺栓和盘组件 (7)。
- 卸下将轴组件 (6) 固定至凸轮轴凸轮段的螺栓。 拆下轴组件。
- 从轴组件上拆下隔套。
Show/hide table
图 1 | g00575670 |
Show/hide table
图 2 | g00575675 |
Caterpillar Information System:
SR4B Generators Coupling - Install
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
3612 and 3616 Engines Piston Cooling Jets - Remove and Install
3114, 3116 and 3126 Engines Unit Injector Misfire
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3612 and G3616 Engines Camshaft - Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove