Camshaft - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 8T-3029 | 凸轮轴支架 | 1 |
1U-6311 | 板 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
组装时必须注意凸轮轴齿块的正确关系。 如果凸轮轴齿块安排的速度不正确,将会严重损坏发动机。
Show/hide table
图 1 | g01529537 |
此图表示凸轮轴轴承轴颈上定位销的位置。 ( X) 凸轮轴轴承颈表面单个定位销的位置。 ( Y) 凸轮轴轴承颈表面可变定位销的位置。 ( Z) 定位槽。 |
Show/hide table
图 2 | g00615517 |
Show/hide table
图 3 | g00615537 |
注: 与可变定位销相关的单个定位销的位置取决于凸轮轴轴颈的指定字符。 单个定位销和定位槽在同一端。 可变定位销位于与定位槽相对的一端。
在定位槽的反面,每个轴颈都有几个销钉孔。 定位槽所在面只有一个销钉孔。 每个轴颈的字母标识均表示定位槽反面轴颈的销钉位置。
Show/hide table
图 4 | g00615565 |
此图示表示 G3612 凸轮轴轴颈的字母名称。 |
Show/hide table
图 5 | g00615568 |
此图示表示 G3616 凸轮轴轴颈的字母名称。 |
- 在组装前,检查定位销的位置和每个凸轮轴轴颈的高度。 每个销的组装高度必须为
15.0 ± 0.5 mm (0.59 ± 0.02 inch) 。注: 对于标准旋转发动机和反向旋转发动机,安装凸轮轴轴颈并使定位槽朝向发动机前部。
对于标准转向发动机,在定位槽朝向发动机前部时安装凸轮轴齿块。
对于反向旋转发动机,在朝向发动机后部的槽安装凸轮轴凸轮段。
Show/hide table图 6 g00615468 - 将干净的发动机油涂抹在后凸轮轴轴承上。
- 将垫片 (3) 放置于轴组件 ( 6) 上的合适位置。 对齐轴组件中的定位销与凸轮轴齿块中的定位销孔。 安装轴组件 (6)。
- 安装将传动轴组件固定至凸轮轴凸轮段的螺栓。 用手上紧螺栓。
- 安装盘组件 (7)和将盘组件固定到位的螺栓。
- 将盘 (8) 和螺栓安装在轴组件 ( 6) 上。
Show/hide table
图 7 g01530616 - 将垫片 (11) 放置于凸轮轴轴颈 ( 2) 的合适位置。
- 在凸轮轴轴颈 (2) 上涂抹干净的发动机机油。 在定位槽朝向发动机前部时,将凸轮轴轴颈安装在凸轮轴轴承中。
- 安装将凸轮轴轴颈固定到凸轮轴齿块的螺栓 ( 3)。 用手上紧螺栓。
- 将垫片 (9) 和垫片 ( 10) 放置于凸轮轴轴颈的合适位置。
- 将工具 (A)安装在缸体侧。
注: 确保凸轮轴齿块中的凹槽处于发动机转向的正确位置。
- 将适当的起吊设备连接到涡轮增压器 ( 4) 上。 凸轮轴凸轮段 ( 4) 的重量约为
28 kg (62 lb) 。 将凸轮轴凸轮段放置于工具 ( A)上的合适位置。 - 将凸轮轴齿块 (4)在工具 ( A)上滚到位。 对齐凸轮轴齿块两端的定位销。 安装螺栓 (8)。 用手上紧螺栓。
- 安装凸轮轴主动齿轮。 更多信息,请参阅 拆解和装配凸轮轴主动齿轮 - 安, "装" 。
- 将所有凸轮轴螺栓拧紧至表 2 中的扭矩。 转动发动机,以拧紧所有螺栓。 轧制扭矩最大为
22 N·m (16 lb ft) 。 必须在凸轮轴后部施加作用力。Show/hide table表 2 螺栓尺寸 扭矩 1/2 in 135 ± 20 N·m (100 ± 15 lb ft) 5/8 in 270 ± 40 N·m (200 ± 30 lb ft) - 检查凸轮轴定时。 更多信息,请参阅 测试和调整凸轮轴定时检 , "查"。
- 将凸轮轴检查盖安装到发动机的一侧。
结束:
- 安装气门挺杆。 请参阅拆解和组装 , "气门挺杆 - 安装"。
Caterpillar Information System:
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
On-Highway Engines Electronic PTO Installation and Application Guide PTO Parameters - Program
G3612 and G3616 Engines Camshaft - Remove
SR4B Generators Coupling - Install
G3612 and G3616 Engines Cylinder Liner - Install
G3612 and G3616 Engines Cylinder Liner - Remove
SR4B Generators Service Tools
3612 and 3616 Engines Piston and Connecting Rods - Install
3114, 3116 and 3126 Engines Unit Injector
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Assemble
3114, 3116 and 3126 Engines Valve Train Noise
C9 On-Highway Truck Engines Air Compressor - Remove and Install
C-9 Industrial Engine Engine Design
3114, 3116 and 3126 MUI Engine Governors Governor (Type VII) - Disassemble
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3304 and G3306 Engines Cylinder Head
3126B Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Remove and Install
C9 Engine For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
SR4B Generators Coupling - Remove
G3304 and G3306 Engines Cylinder Head
C9 Engines for Caterpillar Built Machines Cylinder Liner - Remove
G3612 and G3616 Engines Crankshaft Main Bearings - Install
SR4B Generators Bearing - Remove and Install
G3612 and G3616 Engines Crankshaft - Remove