Camshaft Gear - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6896     | 导向螺栓     | 1     |
开始:
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸"。
- 将 将 1 号活塞定位在压缩冲程的上止点。 请参阅测试和调整, "找到 1 号活塞上止点位置"。
Show/hide table
图 1 | g00579965 |
Show/hide table
图 2 | g00579966 |
- 确认凸轮轴齿轮 (1) 与前壳体 (3) 上的正时标记 (X) 对准。
- 从凸轮轴齿轮 (1) 上拆下顶部螺栓 (2) 。 将工具 (A) 安装到螺栓的位置。
- 拆下剩余的螺栓 (2) ,然后拆下凸轮轴齿轮 (1) 。
- 拆下工具 (A) 。
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6896     | 导向螺栓     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安装到凸轮轴顶部的孔中。
Show/hide table
图 3 | g00579966 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
- 将凸轮轴齿轮 (1) 背面的孔与适配器中的定位销对准。 将凸轮轴齿轮 (1) 安装到工具 (A) 上。
- 确认凸轮轴齿轮 (1) 与前壳体 (3) 上的正时标记 (X) 对准。
注: 如果定时标记没有对准,则拆下凸轮轴齿轮 (1) 并旋转凸轮轴,直到定时标记对准。
Show/hide table
图 4 | g00579965 |
注: 凸轮轴正时至关重要。 当 1 号活塞位于压缩冲程的上止点时,凸轮轴齿轮上的定时标记必须与前盖上的定时标记对准。 请参阅测试与调整, "齿轮总成(前) - 正时"。
- 安装螺栓 (2) 。 拆下工具 (A) ,并安装剩余螺栓 (2) 。
- 按照 1、4、2、5、3、6、1、4 的数字顺序依次拧紧螺栓至扭矩为 240 ± 40 N·m (180 ± 30 lb ft)。
Show/hide table
图 5 | g00593987 |
- 检查凸轮轴齿轮与可调节惰轮齿轮之间的齿隙。 此齿隙应为 0.216 ± 0.114 mm (0.0085 ± 0.0045 in)。 请参阅测试和调整, "齿轮总成(前) - 正时",以了解齿隙调整步骤。
End By: 安装前盖。 请参阅 拆解和组装, "前盖 - 安装"。
Caterpillar Information System:
365B Excavator Hydraulic System Oil (If Equipped with Fine Filtration Filter) - Change
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter (Primary)
Wiring Harness Recommendations For 3500B Locomotive Engines{1408} Wiring Harness Recommendations For 3500B Locomotive Engines{1408}
3412E, C30 and C32 Marine Engines Fuel Filter and Water Separator - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Air Inlet and Exhaust System
G3500 Engines Turbocharger - Remove
3034 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
3176B Marine Engine Sensors and Electrical Components
3176B Industrial Engine Refill Capacities
3412E, C30 and C32 Marine Engines Engine Control Module - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Remove
3412E, C30 and C32 Marine Engines Jacket Water Heater - Remove and Install
G3500 Engines Aftercooler - Remove and Install
3612 and 3616 Engines Engine Oil Pump
3612 and 3616 Engines Engine Oil Pump
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector
3612 and 3616 Engines Engine Oil Pump
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector Mechanism
3034 Engine for Caterpillar Built Machines Inlet Manifold - Remove
3408E and 3412E Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
Installation And Mounting System For Locomotive Engine/Generator Packages{1021} Installation And Mounting System For Locomotive Engine/Generator Packages{1021}