Engine Oil Pump
Show/hide table
图 1 | g00288420 |
(1) 新驱动轴的直径 ... 59.930 ± 0.010 mm (2.3594 ± 0.0004 in)
(2) 驱动轴末端到齿轮表面的距离 ... 169.5 ± 0.5 mm (6.67 ± 0.02 in)
齿轮安装的最大允许温度 ... 316 °C (601 °F)
(3) 惰轮轴末端到齿轮表面的距离 ... 52.5 ± 0.5 mm (2.07 ± 0.02 in)
齿轮安装的最大允许温度 ... 316 °C (601 °F)
(4) 齿轮的长度
- 驱动轴 ... 140.00 ± 0.02 mm (5.512 ± 0.001 in)
- 驱动轴 ... 140.00 ± 0.02 mm (5.512 ± 0.001 in)
(5) 惰轮轴的直径 ... 59.930 ± 0.010 mm (2.3594 ± 0.0004 in)
Show/hide table
图 2 | g00288421 |
(6) 定位销顶面到盖表面的距离 ... 12 ± 1 mm (0.47 ± 0.04 in)
(7) 惰轮轴轴承孔孔径 ... 60.115 ± 0.02 mm (2.3667 ± 0.0008 in)
(8) 盖中的轴承深度 ... 7.50 ± 0.25 mm (0.295 ± 0.010 in)
(9) 驱动轴轴承孔孔径 ... 60.115 ± 0.02 mm (2.3667 ± 0.0008 in)
(10) 将轴承中的油孔对准盖中的油孔。
Show/hide table
图 3 | g00288422 |
(11) 轴承
-
为使压装力最小,冷却轴承和轴承冲头。
- 温度 ... −75 °C (−103 °F) (11) 壳体中轴承的深度 ... 12.30 ± 0.25 mm (0.484 ± 0.010 in)
(12) 壳体中轴承孔孔径 ... 60.126 ± 0.04 mm (2.3672 ± 0.0016 in)
(13) 将轴承中的油孔对准壳体中的油孔。
(14) 齿轮和壳体之间的端隙 ... 0.14 到 0.26 mm (0.006 到 0.010 in)
Show/hide table
图 4 | g00288423 |
(15) 油泵盖组件
- 定位销的高度 ... 8 ± 1 mm (0.32 ± 0.04 in)
(16) 在逆时针旋转的发动机的这个位置上安装定位销。
(17) 在顺时针旋转的发动机的这个位置上安装定位销。
Caterpillar Information System:
3612 and 3616 Engines Engine Oil Pump
G3500 Engines Aftercooler - Remove and Install
3412E, C30 and C32 Marine Engines Jacket Water Heater - Remove and Install
3406E On-Highway Engine Camshaft Gear - Remove and Install
365B Excavator Hydraulic System Oil (If Equipped with Fine Filtration Filter) - Change
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter (Primary)
Wiring Harness Recommendations For 3500B Locomotive Engines{1408} Wiring Harness Recommendations For 3500B Locomotive Engines{1408}
3412E, C30 and C32 Marine Engines Fuel Filter and Water Separator - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Air Inlet and Exhaust System
G3500 Engines Turbocharger - Remove
3034 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector
3612 and 3616 Engines Engine Oil Pump
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector Mechanism
3034 Engine for Caterpillar Built Machines Inlet Manifold - Remove
3408E and 3412E Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
Installation And Mounting System For Locomotive Engine/Generator Packages{1021} Installation And Mounting System For Locomotive Engine/Generator Packages{1021}
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Front Idler
3034 Engine for Caterpillar Built Machines Inlet Manifold - Install
3600 Diesel Marine Monitoring System Fire Prevention and Explosion Prevention
3600 Diesel Marine Monitoring System General Hazard Information