Piston Cooling Jets - Remove and Install
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 9S-9082 | 发动机盘车工具 | 1 |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 拆下螺栓 (1)。 从发动机上拆下活塞冷却喷嘴 (2)。 使用工具 (A) 按顺时针方向转动曲轴，以便接近各活塞冷却喷嘴。 对所有活塞冷却喷嘴重复该过程。
Show/hide table
| |
| 图 1 | g00580930 |
|
典型实例 | |
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 9S-9082 | 发动机盘车工具 | 1 |
| B | 5P-8709 | 冷却喷嘴对准工具 | 1 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (B) 检查活塞冷却喷嘴 (2) 的对准。 请参阅专门说明书, SMHS7267, "使用 5P-8709 工具总成对准活塞冷却喷嘴"，了解正确的对准步骤。
- 将活塞冷却喷嘴 (2) 安装到发动机上。 将螺栓 (1) 上紧到
25 ± 7 N·m (18 ± 5 lb ft) 的扭矩。 使用工具 (A) 按顺时针方向转动曲轴，以便接近各活塞冷却喷嘴。 对所有活塞冷却喷嘴重复该过程。
Show/hide table
|
| |
| 图 2 | g00580930 |
|
典型实例 | |
结束:
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
3034 Engine for Caterpillar Built Machines Inlet Manifold - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector Mechanism
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Install
3034 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove
3612 and 3616 Engines Engine Oil Pump
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Unit Injector
3612 and 3616 Engines Engine Oil Pump
3612 and 3616 Engines Engine Oil Pump
G3500 Engines Aftercooler - Remove and Install
3412E, C30 and C32 Marine Engines Jacket Water Heater - Remove and Install
3406E On-Highway Engine Camshaft Gear - Remove and Install
365B Excavator Hydraulic System Oil (If Equipped with Fine Filtration Filter) - Change
Installation And Mounting System For Locomotive Engine/Generator Packages{1021} Installation And Mounting System For Locomotive Engine/Generator Packages{1021}
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Front Idler
3034 Engine for Caterpillar Built Machines Inlet Manifold - Install
3600 Diesel Marine Monitoring System Fire Prevention and Explosion Prevention
3600 Diesel Marine Monitoring System General Hazard Information
3600 Diesel Marine Monitoring System Mounting and Dismounting
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Disassemble
EMCPII+ for Gas Engines Service Record
3176C and 3196 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
EMCPII+ for Gas Engines AC Factory Calibration Setpoint Viewing OP2-2
EMCPII+ for Gas Engines AC Offset Adjustment OP10
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Sprocket