Aftercooler - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 后冷器有几种可能的配置。 以下程序演示了典型示例。
注: 在 3408E 发动机上执行以下程序。 但是, 3412E 发动机的过程非常相似。
注: 检查密封垫和 O 形圈的状况。 如果密封垫或 O 形圈磨损或损坏,则用新零件更换。
- 如果密封垫已拆下,则安装后冷器壳体的密封垫 (25)。
Show/hide table
图 2 g00579413 典型示例 - 安装先前拆下的后冷器壳体 (23)。
- 安装螺栓 (24) 和垫圈。
Show/hide table
图 3 g00579412 典型示例 - 安装 O 形密封圈 (22)。
- 利用甘油轻轻润滑后冷器壳体内孔和 O 形圈 (22)。
- 安装后冷器芯 (21)。 使用后冷器芯上的起重支架和适当的起吊设备。
后冷器芯组件的重量约为
26 kg (57 lb) 。Show/hide table图 4 g00579409 典型示例 - 安装过渡接头 (16) 和 O 形密封圈 (17)。
- 安装过渡接头 (18) 和 O 形密封圈。
- 利用螺栓 (20) 安装弯头 (19)。
Show/hide table
图 5 g00579407 典型示例 - 安装螺栓 (15) 和垫圈。
Show/hide table
图 6 g00579404 典型示例 - 安装后冷器盖 (14)。
- 安装夹子 (12)、托架 (11) 和螺栓 (13)。
- 利用螺栓 (9) 和 O 形密封圈安装弯头 (10)。
Show/hide table
图 7 g00579403 典型示例 - 利用螺栓 (7) 安装卸压阀壳体 (6)。
- 连接燃油管 (8)。
Show/hide table
图 8 g00579401 典型示例 - 利用螺栓 (3) 安装弯头 (4)。
- 连接燃油管 (1)。
- 将螺栓 (2) 和垫圈安装到夹子内。
- 安装螺栓 (5)、垫圈和隔套。
Show/hide table
图 1 | g00579418 |
典型示例 |
Caterpillar Information System:
3176B Marine Engine Sensors and Electrical Components
3176B Industrial Engine Refill Capacities
3412E, C30 and C32 Marine Engines Engine Control Module - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Remove
3126B Marine Engine General Information
3126B Marine Engine Engine Design
3612 and 3616 Engines Exhaust Manifold
3034 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3412E, C30 and C32 Marine Engines Flywheel Housing - Remove and Install
3034 Engine for Caterpillar Built Machines Glow Plugs - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Duo-Cone Seals - Install
Alignment Procedure for G3500 Tandem Generator Sets{4450} Alignment Procedure for G3500 Tandem Generator Sets{4450}
3034 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
G3500 Engines Turbocharger - Remove
3054 and 3056 Industrial and Generator Set Engines Air Inlet and Exhaust System
3412E, C30 and C32 Marine Engines Fuel Filter and Water Separator - Remove and Install
Wiring Harness Recommendations For 3500B Locomotive Engines{1408} Wiring Harness Recommendations For 3500B Locomotive Engines{1408}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter (Primary)
365B Excavator Hydraulic System Oil (If Equipped with Fine Filtration Filter) - Change
3406E On-Highway Engine Camshaft Gear - Remove and Install
3412E, C30 and C32 Marine Engines Jacket Water Heater - Remove and Install
G3500 Engines Aftercooler - Remove and Install
3612 and 3616 Engines Engine Oil Pump
3612 and 3616 Engines Engine Oil Pump