Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
Start By:
- Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Use a suitable lifting device to support the rear of the engine.
Show/hide table
Illustration 1 g00579266 - Remove bracket (1) from the flywheel housing.
Show/hide table
Illustration 2 g01102533 - Attach Tooling (A) and a suitable lifting device to flywheel housing (5). The weight of the flywheel housing is approximately
45 kg (100 lb) . - Remove bolts (6) and bolts (7).
- Remove bolts (2).
- Remove cover (3) and cover (4).
Show/hide table
Illustration 3 g00579270 - Remove bolt (8).
Show/hide table
Illustration 4 g00579271 - Remove bolts (9) from the oil pan.
- Remove the flywheel housing and the gasket from the cylinder block.
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
B | 230-6262 | Sealant | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install a new gasket on the cylinder block. Apply Tooling (B) to the oil pan gasket.
Show/hide table
Illustration 5 g01102533 Show/hide tableIllustration 6 g00579270 Show/hide tableIllustration 7 g01096238 - Attach Tooling (A) and a suitable lifting device to flywheel housing (5). The weight of the flywheel housing is approximately
45 kg (100 lb) . Position flywheel housing (5) on the cylinder block. - Install bolts (2).
- Install bolts (6) and bolts (7).
- Install bolt (8).
- Tighten the bolts, by using the following procedure.
- In a numerical sequence, tighten Bolt 1 through Bolt 8. Tighten to a torque of
136 ± 14 N·m (100 ± 10 lb ft) . - In a numerical sequence, tighten Bolt 9 through Bolt 17. Tighten to a torque of
55 ± 7 N·m (41 ± 5 lb ft) . - In a numerical sequence, again tighten Bolt 1 through Bolt 8. Tighten to a torque of
136 ± 14 N·m (100 ± 10 lb ft) . - In a numerical sequence, again tighten Bolt 9 through Bolt 17. Tighten to a torque of
55 ± 7 N·m (41 ± 5 lb ft) .
- In a numerical sequence, tighten Bolt 1 through Bolt 8. Tighten to a torque of
- Install cover (3) and cover (4).
Show/hide table
Illustration 8 g00579271 - Install bolts (9) for the oil pan. Tighten the bolts for the oil pan to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .Show/hide tableIllustration 9 g00579266 - Install bracket (1) on the flywheel housing.
End By:
- Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar Information System:
3034 Engine for Caterpillar Built Machines Glow Plugs - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Duo-Cone Seals - Install
Alignment Procedure for G3500 Tandem Generator Sets{4450} Alignment Procedure for G3500 Tandem Generator Sets{4450}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter and Water Separator
G3500 Engines Camshaft Bearings - Install
G3500 Engines Camshaft Bearings - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Final Drive
584 and 584HD Forwarders Work Tools
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Final Drive
Generator Set Control Panel for Switchgear Conversion Modes of Operation
3034 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
3034 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3612 and 3616 Engines Exhaust Manifold
3126B Marine Engine Engine Design
3126B Marine Engine General Information
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Remove
3412E, C30 and C32 Marine Engines Engine Control Module - Remove and Install
3176B Industrial Engine Refill Capacities
3176B Marine Engine Sensors and Electrical Components
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
3034 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
G3500 Engines Turbocharger - Remove
3054 and 3056 Industrial and Generator Set Engines Air Inlet and Exhaust System