Camshaft Bearings - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-4077 | Camshaft Bearing Tool Group | 1 |
125-2739 (1) | Bearing Pilot | 1 | |
125-2740 (1) | Back Up Plate | 1 | |
125-2741 (1) | Bearing Sleeve | 1 | |
B | 8S-2241 | Camshaft Bearing Tool Group | 1 |
C | 316-1493 | Hydraulic Puller As | 1 |
D | 8H-0684 | Ratchet Wrench | 1 |
Show/hide table
(1) | Alternate Tooling for camshaft bearings with a large diameter |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install camshaft bearing (1) on Tooling (A).
Note: Tooling (B) can be used to install the camshaft bearings when the flywheel housing and the front housing have been removed.
Show/hide tableIllustration 2 g02108639 Rear View
(X) Location of camshaft bearing joints
(Y) Location of oil holes - Position camshaft bearing (1) and Tooling (A) in the bore.
Note: The camshaft bearing joint must be on the horizontal centerline of the bore. The upper oil hole must be 20 ± 5 degrees above the horizontal centerline of the bore. The lower oil hole of the camshaft bearing must be 20 ± 5 degrees below the horizontal centerline of the bore. The camshaft bearing joints must face the inside of the cylinder block.
Show/hide tableIllustration 3 g00578349 - Install Tooling (C) on Tooling (A) and pull the camshaft bearing into the bore.
Note: Tooling (D) can be used in place of Tooling (C).
- Check the bore of the camshaft bearing after installation. The bore must be
86.00 ± 0.06 mm (3.385 ± 0.002 inch) .
Show/hide table
Illustration 1 | g00578338 |
Typical example |
End By:
- Install the camshafts. Refer to Disassembly and Assembly, "Camshaft - Install".
Caterpillar Information System:
G3500 Engines Camshaft Bearings - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Install
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Final Drive
584 and 584HD Forwarders Work Tools
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Final Drive
Generator Set Control Panel for Switchgear Conversion Modes of Operation
3034 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
3176B Industrial Engine Sensors and Electrical Components
3612 and 3616 Engines Prelube Pump
3612 and 3616 Engines Prelube Pump
G3500 Engines Cylinder Liner - Install
797 Off-Highway Truck Power Train Differential and Bevel Gear
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter and Water Separator
Alignment Procedure for G3500 Tandem Generator Sets{4450} Alignment Procedure for G3500 Tandem Generator Sets{4450}
784C and 785C Off-Highway Trucks Machine Systems Duo-Cone Seals - Install
3034 Engine for Caterpillar Built Machines Glow Plugs - Remove and Install
3412E, C30 and C32 Marine Engines Flywheel Housing - Remove and Install
3034 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3612 and 3616 Engines Exhaust Manifold
3126B Marine Engine Engine Design
3126B Marine Engine General Information
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Remove
3412E, C30 and C32 Marine Engines Engine Control Module - Remove and Install
3176B Industrial Engine Refill Capacities