Cylinder Liner - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-9895 | Crossblock | 1 |
3H-0465 | Push Puller Plate | 2 | |
8F-6123 | Bolt | 2 | |
0S-1575 | Bolt | 4 | |
- | Washer (3/4 inch Copper) | 4 | |
B | 8T-0455 | Liner Projection Tool Group | 1 |
C | 2P-8260 | Cylinder Liner Installer | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the spacer plate gasket and the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and Install".
Note: Ensure that all surfaces are clean and dry when the spacer plate gasket is installed.
- Clean the cylinder liner and the cylinder bore in the cylinder block.
- Position the cylinder liner in the cylinder bore without the seals or the filler band.
Show/hide table
Illustration 1 g00578873 Typical example - Use the following steps to check the cylinder liner projection:
- Install four bolts (4) and the washers from Tool (A). Tighten the bolts evenly in four steps.
Step 1 ...
14 N·m (10 lb ft) Step 2 ...
35 N·m (25 lb ft) Step 3 ...
70 N·m (50 lb ft) Step 4 ...
95 N·m (70 lb ft) - Install crossbar (2), plates (3), and bolts (1) from Tool (A). Ensure that crossbar (2) is in position at the center of the cylinder liner. Also ensure that the surface of the cylinder liner is clean. Tighten bolts (1) evenly in four steps.
Step 1 ...
7 N·m (5 lb ft) Step 2 ...
20 N·m (15 lb ft) Step 3 ...
35 N·m (25 lb ft) Step 4 ...
70 N·m (50 lb ft) - Check the distance from the bottom of crossblock (2) to the top of the spacer plate. The distance at both ends of the crossbar must be equal.
- Check the liner projection with Tool (B) at four locations on the cylinder liner. The cylinder liner projection must be
0.129 ± 0.070 mm (0.0051 ± 0.0028 inch) . A distance of0.05 mm (0.002 inch) must be the maximum difference between the measurements.Note: If the cylinder liner is turned in the cylinder block, there will be a difference in the liner projection.
Show/hide tableIllustration 2 g00578874 - Install four bolts (4) and the washers from Tool (A). Tighten the bolts evenly in four steps.
- If the liner projection is not
0.129 ± 0.070 mm (0.0051 ± 0.0028 inch) , check the thickness of the following items:(5) Spacer plate ...
12.313 ± 0.025 mm (0.4848 ± 0.0010 inch) (6) Spacer plate gasket ...
0.208 ± 0.025 mm (0.0082 ± 0.0010 inch) (7) Cylinder liner flange ...
12.65 ± 0.02 mm (0.498 ± 0.001 inch) - Place an alignment mark on the cylinder liner and the cylinder block in order to install the cylinder liner in the same position.
- Remove Tool (A), Tool (B), and the spacer plate. Also remove the cylinder liner.
Show/hide table
Illustration 3 g00578875 Typical example - Apply liquid soap to seals (5), the grooves of the cylinder liner, and the cylinder block.
- Install seals (5) on the cylinder liner.
- Dip the filler band (6) in clean engine oil. Immediately install filler band (6) in the groove that is under the cylinder liner flange.
Show/hide table
Illustration 4 g00578876 Typical example - Install the cylinder liner immediately after filler band (6) is installed on the cylinder liner. Ensure that the marks that are on the cylinder liner and the cylinder block are aligned.
- Use Tool (C) to press the cylinder liner into the cylinder block.
End By:
- Install the pistons and the connecting rod assemblies.
Caterpillar Information System:
797 Off-Highway Truck Power Train Differential and Bevel Gear
3034 Engine for Caterpillar Built Machines Flywheel - Install
3406E Generator Set Engines Information Plate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Dedicated Shutdown Indicators
3034 Engine for Caterpillar Built Machines Flywheel - Remove
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
G3500 Engines Cylinder Liner - Remove
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System CID 0175 FMI 08 Temperature Sender (Engine Oil) Abnormal Signal - Test
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Install
3612 and 3616 Engines Prelube Pump
3612 and 3616 Engines Prelube Pump
3176B Industrial Engine Sensors and Electrical Components
3034 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
Generator Set Control Panel for Switchgear Conversion Modes of Operation
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Final Drive
584 and 584HD Forwarders Work Tools
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Final Drive
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Install
G3500 Engines Camshaft Bearings - Remove
G3500 Engines Camshaft Bearings - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter and Water Separator