Flywheel - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | FT-1342 | 导向螺栓 | 2 |
B | 138-7575 | 连杆支架 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将齿圈加热到
300 °C (572 °F) 的最高温度后安装到飞轮上。 确保飞轮安装后,轮齿的斜面面向起动机小齿轮。Show/hide table图 1 g00578491 典型示例。 显示的工具 (B) 不是表中列出的工具。 - 将工具 (A) 安装到曲轴中。
- 将工具 (B) 固定到起重机上。 将此工具安装到飞轮 (2) 的环槽中。
飞轮的重量约为
78 kg (172 lb) 。 - 将飞轮 (2) 定位到工具 (A) 上。
Show/hide table
图 2 g00578492 典型示例 - 将干净的机油或 5P-0960 含钼润滑脂涂抹到螺栓 (2) 的螺纹上。
- 安装其中的六条螺栓。
- 拆下工具 (A) 和 (B)。
- 安装其余螺栓 (2)。 拧紧所有螺栓至扭矩为
270 ± 40 N·m (200 ± 30 lb ft) 。 - 检查飞轮的跳动。
注: 关于飞轮跳动检查的信息,请参阅测试和调整, "飞轮-检查"。
注: 关于飞轮的更多信息,请参阅技术参数, "飞轮"。
Caterpillar Information System:
3034 Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel - Remove
797 Off-Highway Truck Power Train Gear Pump (Rear Axle Oil)
3176B Industrial Engine Gauges and Indicators
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Transfer Pump
3176C and 3196 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3176B Industrial Engine Engine Description
3612 and 3616 Engines Exhaust Manifold
G3500 Engines Camshaft - Install
G3500 Engines Camshaft - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines SP Fault Code - Troubleshoot
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System CID 0175 FMI 08 Temperature Sender (Engine Oil) Abnormal Signal - Test
G3500 Engines Cylinder Liner - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Dedicated Shutdown Indicators
3406E Generator Set Engines Information Plate
3034 Engine for Caterpillar Built Machines Flywheel - Install
797 Off-Highway Truck Power Train Differential and Bevel Gear
G3500 Engines Cylinder Liner - Install