Exhaust Manifold - Remove and Install
Removal Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove eight bolts (1) from exhaust manifold (2) .
Show/hide table
Illustration 1 | g00578523 |
- Remove exhaust manifold (2) and gasket (3) from the engine.
Show/hide table
Illustration 2 | g00578529 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Make sure that the cylinder head and the exhaust manifold are clean and free of carbon and gasket material.
- Install two guide bolts (4) into two of the bolt holes for the exhaust manifold bolts. The guide bolts are used to keep exhaust manifold gasket (3) and exhaust manifold (2) in position on the cylinder head during installation.
Show/hide table
Illustration 3 | g00578574 |
- Put a new exhaust manifold gasket (3) in position on the engine. It is not necessary to use a sealer on the exhaust manifold gasket.
- Put exhaust manifold (2) in position on the engine.
Show/hide table
Illustration 4 | g00578523 |
- Install six of the eight bolts (1) and remove the two guide bolts. Install the remaining two bolts (1) .
- Tighten eight bolts (1) in an outward pattern. Begin with the center of the exhaust manifold. Tighten bolts (1) to a torque of 18 N·m (13 lb ft).
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel - Remove
797 Off-Highway Truck Power Train Gear Pump (Rear Axle Oil)
3176B Industrial Engine Gauges and Indicators
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Transfer Pump
3176C and 3196 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3176B Industrial Engine Engine Description
3612 and 3616 Engines Exhaust Manifold
G3500 Engines Camshaft - Install
G3500 Engines Camshaft - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines SP Fault Code - Troubleshoot
3406E On-Highway Engine Crankshaft Main Bearings - Install
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Install
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System CID 0175 FMI 08 Temperature Sender (Engine Oil) Abnormal Signal - Test
G3500 Engines Cylinder Liner - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Dedicated Shutdown Indicators
3406E Generator Set Engines Information Plate
3034 Engine for Caterpillar Built Machines Flywheel - Install
797 Off-Highway Truck Power Train Differential and Bevel Gear