Flywheel - Remove
Removal Procedure ( 3003 Engine)
Start By:
- Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) .
Show/hide table
Illustration 1 | g00582471 |
- Remove flywheel (2) .
- If removal of the flywheel ring gear is necessary, place an index mark on the flywheel and the flywheel ring gear for the installation process.
- Use a hammer and a punch in order to remove flywheel ring gear (3) from flywheel (2) .
Show/hide table
Illustration 2 | g00683054 |
Typical example |
- Inspect the flywheel ring gear and the flywheel for wear or damage. If the flywheel ring gear or the flywheel is worn or damaged, use new parts for replacement.
Removal Procedure ( 3013, 3014, and 3024 Engines)
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 1     |
B     | -     | Guide Bolt (M10 x 1.25 mm)     | 2     |
Start By:
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2) is approximately 34 kg (75 lb).
Show/hide table
Illustration 3 | g00582825 |
- Remove two bolts (1) opposite each other from the flywheel.
- Install Tooling (B) .
- Remove remaining bolts (1) .
- Remove flywheel (2) .
Show/hide table
Illustration 4 | g00584293 |
- If removal of the flywheel ring gear is necessary, place an index mark on the flywheel and the flywheel ring gear for the installation process.
- Use a hammer and a punch in order to remove flywheel ring gear (3) from flywheel (2) .
Show/hide table
Illustration 5 | g00683054 |
Typical example |
- Inspect the flywheel ring gear and the flywheel for wear or damage. If the flywheel ring gear or the flywheel is worn or damaged, use new parts for replacement.
Caterpillar Information System:
797 Off-Highway Truck Power Train Gear Pump (Rear Axle Oil)
3176B Industrial Engine Gauges and Indicators
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Transfer Pump
3176C and 3196 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3176B Industrial Engine Engine Description
3612 and 3616 Engines Exhaust Manifold
G3500 Engines Camshaft - Install
G3500 Engines Camshaft - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines SP Fault Code - Troubleshoot
3406E On-Highway Engine Crankshaft Main Bearings - Install
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Install
3034 Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Install
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System CID 0175 FMI 08 Temperature Sender (Engine Oil) Abnormal Signal - Test
G3500 Engines Cylinder Liner - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Dedicated Shutdown Indicators
3406E Generator Set Engines Information Plate
3034 Engine for Caterpillar Built Machines Flywheel - Install